Kenmore Washer 796.40448900 (79640448900, 796 40448900) Parts

Includes sensor probe

This pivot hanger assembly supports and stabilizes the appliance component it mounts to, restoring smooth movement and alignment. Replace a worn or damaged pivot to reduce noise and prevent misalignment that can affect operation. What it does:

• Acts as the pivot point for the hanger to support the drum/door assembly and maintain correct alignment
• Helps eliminate squeaks, scraping, or jerky motion caused by a worn pivot
• Prevents sagging or uneven movement that can lead to rubbing or binding
• Restores proper mechanical support so the appliance operates quietly and reliably

• Unplug the appliance or disconnect power before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Inspect surrounding components (mounts, bearings, fasteners) and replace if worn

This balance weight stabilizes the washer tub during spin cycles to reduce vibration and excessive movement, helping restore quieter operation and prevent further stress on suspension components and fasteners. What it does

• Counters the rotating tub to reduce vibration and rocking during spin cycles.
• Helps stop excessive movement, banging noises, and uneven spinning that can indicate an unbalanced load or worn mounting hardware.
• Replaces a damaged or missing counterweight to regain stable, consistent spin performance.
• Mounts to the washer cabinet/tub area and secures with factory fasteners.

• Disconnect power and water supply and run a drain/spin or remove standing water before beginning work.
• Removing the washer cabinet or front panel is often required; support the tub and components while you work.
• Use appropriate hand tools and keep OEM fasteners for reinstallation; follow the appliance service manual for exact steps.
• Wear gloves and eye protection.

Locking pin for shock absorber.

This hose connector joins a refrigerator's/dispenser's water line to internal plumbing, restoring a secure, leak-resistant connection. It replaces cracked or worn connectors to help stop leaks and ensure reliable water flow. What it does:

• Provides a sealed connection between the water hose and the appliance plumbing or valve
• Stops leaks caused by cracked, brittle, or damaged connectors
• Restores proper water flow to the dispenser/ice maker when the connector is the failure point
• Works with hose clamps or fittings already present in the appliance plumbing

• Shut off water supply and unplug the appliance before servicing
• Inspect hose ends and replace clamps or O-rings if damaged; use proper-size clamps for a secure fit
• Hand-start threads, then tighten snugly—avoid over-tightening plastic fittings to prevent damage
• Turn water back on and check thoroughly for leaks after installation

This rear cover is the outer housing panel that protects the appliance's internal components and helps maintain proper airflow and support. It replaces a cracked, broken, or missing rear housing panel to restore protection and fit. What it does:

• Shields motors, wiring, vents, and other internal parts from dust, debris, and accidental contact
• Helps direct airflow and maintain correct ventilation for safe operation
• Restores proper mounting points and prevents rattles from a loose or damaged back panel
• Commonly replaced when there is visible damage, missing mounting tabs, or unusual noise from the rear

• One rear cover

• Disconnect power (unplug or switch off circuit breaker) before starting any repair
• Removal usually requires taking off the exterior panels and a few screws or clips; retain all fasteners for reinstallation
• Watch for sharp edges and wear protective gloves; handle internal wiring and components gently

This water level pressure switch senses the washer tub's water level and signals the control to start or stop filling. It restores accurate fill detection for proper wash cycles and helps prevent overfilling or improper operation. What it does:

• Detects water level via a vacuum hose and tells the control board when to stop filling
• Helps prevent overfill, underfill, and related cycle interruptions
• Can resolve symptoms like washer not filling, overfilling, or stopping mid-cycle
• Works as the sensing interface between the tub and the control system

• One water level pressure switch assembly

• Disconnect power and shut off water supply before replacing the part
• Note the vacuum hose routing and electrical connector locations before removal
• Handle the small vacuum hose and plastic fittings gently to avoid damage or air leaks

This holder is a small mounting bracket that secures internal components and keeps assemblies aligned for reliable operation. It replaces a worn or broken bracket to stop rattling and prevent parts from shifting. What it does

• Secures and positions nearby components or assemblies to maintain correct alignment
• Prevents vibration, rattling, or intermittent contact caused by a loose or cracked bracket
• Restores proper spacing so sensors, panels, or moving parts operate smoothly
• Helps prevent further wear or damage from misaligned parts

• One holder as shown

• Turn off power and disconnect the appliance before attempting any repairs
• Installation typically requires basic hand tools; save removed screws and clips for reassembly