Lg Dryer TDV70120E Parts

The Noise Filter Assembly is an OEM part for LG washing machines, designed to minimize electrical noise interference within the appliance. This essential component ensures that the washer operates smoothly without emitting disruptive sounds that can affect both the performance of the washer and the comfort of your home environment. 

Causes of a bad Noise Filter Assembly can range from wear and tear over time to exposure to power surges or electrical spikes, which can damage the internal components of the filter. 

Symptoms of a bad Noise Filter Assembly include:

• Increased electrical noise or buzzing sounds emanating from the washer
• Intermittent disruptions in the washer's performance
• The washing machine failing to start or experiencing power fluctuations

This OEM LG part is also compatible with some Kenmore models.

The Light Bulb is an OEM part for LG dryers. This bulb illuminates the interior of the dryer drum, making it easier to see and load or unload laundry, especially in low-light conditions.

Over time, the light bulb can burn out or become damaged due to regular use and exposure to high temperatures within the dryer. Causes of a bad light bulb include normal wear and tear, electrical surges, or physical damage to the bulb.

Symptoms of a bad light bulb include:

• The interior of the dryer remaining dark when the door is opened
• Flickering or dim lighting
• No response from the light even after replacing the bulb

This OEM LG part is also compatible with Sears/Kenmore dryers.

This NTC thermistor is the dryer's temperature sensor. It monitors exhaust air temperature and signals the control to cycle the heat, restoring accurate drying performance and helping prevent overheating, underheating, and inconsistent results.

• Monitors exhaust air temperature by changing resistance as heat rises (NTC behavior)
• Sends temperature feedback to the control to regulate the heater or gas valve
• Failure can cause no heat, overheating, or erratic temperatures
• May lead to long dry times, short cycles, or temperature-related error codes

• Disconnect power and, for gas models, shut off the gas supply before servicing
• Access the sensor on the blower housing or exhaust duct; location varies by model
• Note wire routing; unplug the harness connector; remove the mounting fastener/clip; install the new sensor fully seated and reconnect
• Reassemble, restore power, and run a test cycle; check and clean venting to ensure proper airflow

Dryer not heating or overheating? This thermostat assembly regulates temperature to prevent damage and maintain consistent drying. Easy DIY repair.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

This adjustable leg assembly raises and levels the appliance to keep it stable and reduce rocking. It provides a simple way to set appliance height for proper door alignment and smooth operation. What it does:

• Supports the appliance and transfers weight to the floor
• Allows height adjustment to level uneven floors
• Helps prevent excessive vibration, rocking, and noise
• Promotes proper door/drawer alignment and seal

• One leg assembly

• Disconnect power and empty the appliance before adjusting or replacing legs
• Raise or support the appliance safely before removing or installing the leg
• Adjust by turning the leg; tighten securely but avoid over-torquing

Dryer drum glide slider that supports the front of the drum during rotation. Replace if cracked, worn, or causing noise from drum misalignment.

This damper assembly controls fresh air flow into the refrigerator compartment to help regulate internal temperatures. Replaces the factory air inlet damper to restore proper airflow between compartments. What it does:

• Opens and closes the fresh air inlet to control air exchange between compartments
• Helps maintain consistent refrigerator temperatures by regulating incoming air
• Common symptoms: uneven cooling, warm refrigerator compartment, or inconsistent temperatures

• One fresh air damper assembly

• Disconnect power before servicing to avoid electrical shock
• Handle the damper gently to avoid bending the flap or damaging the actuator
• Typically installs with a few screws and simple connectors; verify orientation before tightening

Secures dryer panels, brackets, and trim pieces. Replace this fastener if missing, stripped, or damaged to restore proper assembly and safe operation.

Dryer not tumbling clothes properly? A worn drum lifter causes poor drying and tangled loads. This repair takes 30-45 minutes with basic tools.

Flat metal washer that spaces and secures internal fasteners in your dryer. Replace when worn or during repairs to maintain proper alignment. Confirm fit with your model number.