Thermador Range PRD364GDHC Parts

The Spark Ignition Switch is an OEM part for Bosch ranges and cooktops. It controls the ignition of surface burner flames by emitting an electrical spark when activated.

Causes of a bad switch can be general wear and fatigue over thousands of start cycles. Exposure to moisture, dust or metal debris could also damage electrical components internally.

Symptoms of a bad spark ignition switch include:

• Burners failing to light even when valves are turned on
• Intermittent or irregular lighting of some burners
• No electrical sparks emitted from the ignition electrode

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Fix a range that won't reach set temperature or shows temperature error codes. This sensor monitors oven heat and signals the control board to adjust.

Replacement rubber feet for gas cooktop grates. Kit includes 4 feet and adhesive. Needed when original feet are cracked, worn, missing, or fell off.

This is a spark ignition switch used on a range or cooktop that controls the electric spark to ignite the surface burners when the control knob is turned. It connects to the burner igniter circuit and signals when to fire the spark module. Replace this switch if your burners won't ignite, the spark clicks continuously even after the flame is lit, or the igniter fails to spark when the knob is engaged.

Mounting screw secures burner components and panels on gas ranges. Replace if stripped, corroded, or broken to restore proper alignment and fit.

Telescopic oven rack designed for gas ranges. Slides out smoothly for easy access while cooking or cleaning. Replace if damaged, warped, or worn.

Fixes burner not getting gas or won't ignite. Solenoid valve controls gas flow to individual burners. Moderate DIY repair for gas ranges and cooktops.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Controls gas supply pressure to burner manifold. Replace if regulator is cracked, sticking, or no longer maintaining correct pressure for consistent flames.

Gas burners won't light or keep clicking? This spark module generates consistent sparks to reliably ignite cooktop burners for safe operation.

This OEM replacement part is a motor assembly for ovens. The motor assembly is the main motor that powers the oven fan which is responsible for maintaining and adjusting the temperature in an oven. If the oven is no longer heating properly, turning on, or maintaining temperature, then the motor assembly will need to be replaced.To replace this part, make sure that the oven is unplugged. After it has been powered off, proceed to pull the oven out and away from the wall. Once moved, uninstall the back panel of the oven by removing the panel's mounting screws. After detaching the back panel, locate the motor housing on the back of the oven. Unthread the screws that hold the housing in place. Once removed, locate the mounting brackets that hold the motor in place and remove the screws that attach to the motor. Pull the old motor out of its place and install the new motor. Reinstall the back panel and restore power to the appliance.This genuine replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador brand ovens.

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

This rotary potentiometer converts shaft rotation into an electrical signal the control board can read, providing precise position feedback for user selections. Replace it if inputs become erratic, jump between settings, or the control stops responding.

• Provides rotary position feedback to the electronic control
• Enables accurate selection and adjustment of functions or setpoints
• Wear or damage can cause drifting, dead spots, or incorrect readings
• Intermittent or no response to input is a common failure symptom

• Disconnect power before servicing
• Access the control/console area to reach the component
• Note shaft orientation and any connector positions; transfer exactly to the new part
• Handle electronics with ESD care and verify smooth, full-range operation after reassembly

Fix an oven light that won't turn on or a self-clean cycle that won't start. This door switch monitors door position for safety and lighting.

This indicator light illuminates to show when a burner or oven element is active or still hot. It is mounted on the control panel and provides a visual safety alert during and after cooking. Replace this part if the indicator fails to light up when a burner is on, stays lit continuously, or appears dim and flickering.

This circular heating element is mounted around the convection fan at the rear wall of the oven cavity. It provides the heat that the fan circulates evenly throughout the oven during convection cooking. Replace this element if the oven does not heat properly in convection mode, heats unevenly, or if the element shows visible damage such as blistering, cracks, or burn-through spots.