Power Tools Parts

Best Seller

Genuine Whirlpool part

Container Roller Bearing (Trash Compactor)

By: Whirlpool

Part Number: WP9871602

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

Provides low-friction support so the drawer glides smoothly on the tracks
Helps maintain proper container alignment and stability
Reduces squeaks, grinding, and sticking during operation
Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

What's included: 1 container roller bearing Installation notes:

Disconnect power to the compactor before servicing
Remove and empty the drawer to access the bearing location
Install the new bearing in the same orientation; transfer any hardware as needed
Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Do-It-Yourself Stories from Customers like You My 30 year old whirlpool trash compactor roller bearings are "worn out"! L H. • Villa Grande , CA • January 17, 2015

Bot both sets of roller bearings, lower ones on the appliance and the set on the trash can that rolls out. I just followed the instructions that were in the roller bearing package and only needed the tools that are recommended. Was a little tricky with the nuts, really need a person with "small" fingers to reassemble the nuts back on the lower set of bearing that are on the appliance. All in All, went well and works. Found that the new bearings are v. tight on the machine, being new, so, use... Read more

$15.95

Compare At:: $18.98
You Save:: $3.03

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Best Seller

Genuine Whirlpool part

Screw

4.7 (6)

By: Whirlpool

Part Number: WP489478

Size: 8 x 1/2 ab.

Do-It-Yourself Stories from Customers like You Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

$5.95

Compare At:: $7.02
You Save:: $1.07

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Whirlpool part

Refrigerator Container Handle (Black)

4.9 (19)

By: Whirlpool

Part Number: WP608732

This black refrigerator container handle replaces a worn, cracked, or missing pull on an interior bin or drawer. It restores a secure grip so you can easily slide the container in and out on compatible models.

Attaches to the front of a refrigerator container or its cover to provide a solid handhold
Replaces cracked, loose, or missing handle pieces
Helps bins open and close smoothly without stressing the cover/front
Common symptoms: handle broken or missing, tabs snapped, handle won't stay attached, drawer hard to pull

What's included: 1 black container handle Install notes:

Remove the bin/drawer and place the cover or front on a flat, protected surface
Release the old handle by removing screws or disengaging tabs/clips (varies by model); keep hardware for reuse
Align the new handle and snap or screw it into place; do not overtighten
Handle glass and plastic parts carefully; wearing cut-resistant gloves is recommended

Do-It-Yourself Stories from Customers like You Broken handle on trash compactor Lydia R. • Modesto , CA • February 07, 2015

Ordered the part, which arrived incredibly fast and switched out old one for the new. Read more

$99.72

Compare At:: $118.67
You Save:: $18.95

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Whirlpool part

Switch Nut

5.0 (2)

By: Whirlpool

Part Number: WP777383

This switch nut secures a rotary control or switch to the appliance's front panel. Replacing a stripped or missing nut keeps the control stable so the knob turns smoothly and the shaft stays properly aligned.

Clamps the switch/control to the panel to prevent movement or rotation
Helps maintain correct knob alignment with dial markings
Common symptoms: loose or wobbly knob, switch rotates in the panel, missing/damaged nut
Often needed after service if the original nut is stripped or lost

What's included: 1 switch nut Install notes:

Disconnect electrical power before servicing
Remove the knob and any decorative escutcheon; thread the new nut onto the switch bushing from the front of the panel
Support the switch from behind while tightening; do not overtighten to avoid panel or switch damage
Restore power and test control operation

Do-It-Yourself Stories from Customers like You The trash compactor would not shut off. Robert T. • Anchorage , AK • November 06, 2022

I replaced the upper-end Directional Switch for $45. Read more

$7.61

Compare At:: $9.13
You Save:: $1.52

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Whirlpool part

Use 41001100

5.0 (1)

By: Whirlpool

Part Number: WP776356

Size: 3\8-24 inch.

Do-It-Yourself Stories from Customers like You Trash compactor one roller was missing and the handle cracked several times had been super glued too often Thomas N. • Hill Country Village , TX • January 28, 2020

After I was shocked at the price to replace the trash compactor, I was happy to find that the parts, both front & back rollers and the handle, were available from AppliancePartsPros.com. They arrived as scheduled and after viewing two videos, the job went very smooth. I hope it puts another 27 years life into the unit. Read more

$5.95

Compare At:: $7.02
You Save:: $1.07

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Whirlpool part

Container Spring (Replacement)

5.0 (2)

By: Whirlpool

Part Number: WP777180

This replacement container spring helps restore proper tension and support for the container assembly, so the container stays secure and operates smoothly. Ideal when the original spring is worn, stretched, or broken. What it does:

Provides tension to hold the container or bin in its intended position
Replaces worn or broken springs that cause slipping or poor engagement
Stops rattling or shifting caused by a weakened spring
Helps the container latch, release, or return smoothly during use

What's included: One container spring Install notes:

Basic hand tools may be required; follow the appliance's service manual for access and removal
Disconnect power (and water if applicable) before servicing to prevent injury
Handle small parts carefully to avoid pinching; springs can store tension

Do-It-Yourself Stories from Customers like You Spring Robert L. • Swall Meadows , CA • February 02, 2020

New spring. Read more

$45.95

Compare At:: $54.68
You Save:: $8.73

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Whirlpool part

Cone Washer

5.0 (1)

By: Whirlpool

Part Number: WP777332

This small conical washer is used in select washer assemblies to maintain clamp force under vibration. It helps keep fasteners tight and components properly aligned for reliable wash and spin performance. What it does:

Provides spring-like tension under a screw or bolt to maintain clamp load
Helps prevent fasteners from loosening due to vibration
Supports proper alignment and secure fit of mating parts
Worn or missing washers can lead to rattling, looseness, or intermittent operation

What's included:

1 cone washer

Install notes:

Disconnect power and, if applicable, turn off water supply before servicing
Access the relevant assembly per your model's service information
Note the washer's original orientation and match it during reassembly
Tighten hardware securely without over-torquing; test and recheck for security

Do-It-Yourself Stories from Customers like You Spider bearing failed and the chain locked, which caused the big gear to break on my GE trash compactor. Kelly G. • Heber Springs , AR • January 25, 2020

Replaced all damaged parts. Read more

$4.73

Compare At:: $5.58
You Save:: $0.85

IN STOCK

Ships Tomorrow Guaranteed

Add to Cart

Genuine Mtd part

Shoulder Screw

By: Mtd

Part Number: 938-0373

Here is a replacement shoulder screw that is commonly used for various types of outdoor power equipment. Another name for the shoulder screw is a shoulder pin. The screw is often used to help secure the plastic wheels to the deck of a machine. However, different machines may have different uses for shoulder screws and other types of hardware. The shoulder screw is made from metal and is durable. However, the pin may still need to be replaced at some point. Whether it is because of corrosion or being bent, it is important to replace a failed screw with a new one. When performing maintenance on the machine, it is also possible that the screw could become lost, which would require a replacement. This is a genuine OEM replacement shoulder screw. It is sold individually and works with many types of makes and models. The screw is often used for edgers, snowblowers, lawn mowers, and chainsaws. Brands that have models that will be compatible with the shoulder screw include Craftsman, Toro, Cub Cadet, Troy-Bilt, Yard Machines, MTD, Huskee, Yard-Man, and MasterCut.

$10.95