Riley July 03, 2020 for Model Number HEI7282U/01 The Red internal wires at the terminal block have the ring terminal damaged due to the power cord melting at the terminal block. The red wires That Are left with only 1/2 of the ring go to the control board. These wires have continuity. Board does not have any obvious damage. Can I buy new red wires/ring terminal? Or new wiring harness that goes from control board to terminal block? Thanks!
1 Answer Riley, Unfortunately, the manufacturer is not listing the harness that goes from the terminal block to the power board. You would most likely be able to get a connector and cut and splice the wire to repair it. Read More...
Charles March 02, 2019 Hello, I have a Bosch electric range/oven, Model HEI7282U/01. Various functions have started coming on by themselves: oven light, the off signal (3 beeps), and even the oven itself comes on and heats up sometimes. All of this is randomly happening completely by itself. Would this be the power module, the control board, or something else? Thank you for any help you can give, Charles Thornton
1 Answer Charles, It's more likely to be something else. The more likely issue is the keypad/membrane assembly on the control panel 00703427 / 00703427 Panel, and/or the ribbons between the control panel and the 00653424 / 00653424 Module/ Clock. Read More...
Dave January 20, 2019 for Model Number HE17052U All Heating elements working. Temp is controlled in Convection Bake,Convection Roast,Temp cycles @ setpoint +/- as expected. In BAKE mode Preheats to setpoint temp no problem but when temp cycles down it will not return to heat
1 Answer Dave, Check the oven sensor at room temperature for resistance, it should read 1080 ohms. If the resistance is correct, I would recommend changing the control board, you may have a relay that is not opening and closing properly. Also, the oven sensor can read good at room temperature but fail once it heats up. Read More...
Miguel January 07, 2019 My HDI7282U/06 just broils and gets hot, regardless of what I program the oven to do. The broiler is on during bake, proofing, etc... I replaced the front control board. Do I need to replace the rear board, or is this there a reset button? If I have to replace the rear board, can you please tell me if you carry them and what the part number is? Thanks.
1 Answer Miguel, It sounds like the broil relay is stuck closed and the rear control needs replaced.00657860 Read More...
Zack December 02, 2018 for Model Number HDI7052U/03 What can be wrong with error 160 unite was from 2009 Thanks
1 Answer Zack, This issue would be caused by a hall effect sensor on the cooling fan not present. This will most likely be an issue with the blower 00448635. Read More...
Ben February 15, 2017 for Model Number Bosch HDS7152U Oven heating element will not come back on after reaching the set temperature. Does get to the correct temp, but heating elements wont come back on until I turn oven off and turn back on. Guessing the power control board is bad?
1 Answer Ben, Yes the power board will be the most likely cause for the elements to not come back on once temp is reached. Read More...
George February 27, 2016 for Model Number HE17052U/09 I have a power module #657860 for a Bosch Range. I was told it is a replacement for #651013 The problem is there is one more harness that is supposed to fit it has four orange wires but no where to install it at the top left of the board.
1 Answer George, We show that the 00657860 is the correct part number for your unit. According to the manufacturer there should be instructions with the kit but we do not have the instructions for the part. Read More...
1 Answer Ronnie, To access and replace the power module board, you will need to pull the range out and remove the rear cover. This control board is under the rear cover of the unit. Read More...
Peter March 07, 2014 for Model Number Bosch HEI782U/06 No oven functions work, error code 160. No automatic cleaning, error code 154 after 20 minutes. In autoclean mode entire oven very hot (not possible to touch). Can you tell me what is wrong with it?
1 Answer Peter, The F160 error code is an indication that the cooling fan hall effect feedback is not present. This would most likely be a fan issue. The fan part number is 00448635. Read More...
Evan M. January 14, 2014 for Model Number HEI7152U/03 - Bosch Oven My oven is about 3-4 years old. I do not know what happened but now the oven is heating too much. It appears that the broiler element is on Hi during baking so that the top of whatever I am cooking gets burned. I have already replaced the oven sensor with no change. I am worried it is the control board. Any ideas? Can I return the control board if I order it and it does not fix the oven?
1 Answer Hello Evan, This sounds like the broil relay on the control 00657860 is welded closed. This will require the board to correct. If you need to return it you can do so for 365 days of the date of order as per our return policy. Read More...