Brad August 13, 2024 for Model Number HGPR36S I have the Heritage Gas Range and to replace the thermostat assembly due to a broken stem on the handle. I need to remove the drip tray to access the angle to pass the thermostat into the oven. Will this tool work to remove the burners?
1 Answer Brad, the dual ring burner tool DE81-05222A would be used with the model provided. Read More...
Catriel February 19, 2023 for Model Number ER48DSCHNG I need to access under the tray to replace the board that controls the oven. I bought everything including the tool to remove the burners. But these main burners have something in the center that doesn’t allow the tool to unscrew the ring around it. How do I remove the brass rings from the tube that holds it?
1 Answer Catriel, You may need to turn the burner on to get it hot and then turn off the burner and being very careful to not burn yourself, try to get the ring off. These can seize and the heat can help them to break loose. Read More...
John February 19, 2022 for Model Number Dacor Epicure ER36D Which is the correct tool needed to remove rings on crown burner nozzles so that I can remove the stovetop to repair an LED for one of the burner control knobs that are no longer working? I'm guessing 101539 to allow full rotation, but 86007 could also be it. Thanks!
Steve November 22, 2021 for Model Number Dacor ER30D I need to remove burners to access control boards. I purchased a flat ring tool but it doesn't seat or line up with the notches. I had a cylinder tool ,small pipe that fit over with a hole to allow a small screw driver to turn. is this tool available?
George September 04, 2021 for Model Number Dacor Cooktop RGC365S/NG How exactly does the burner ring tool work? in other words, where do you place it to remove the ring?
1 Answer George, the burner ring tool would fit in the center of the burner rings where it will catch the nodes. This will allow the tool to be used to rotate the burner ring for removal. Read More...
Robert March 21, 2020 for Model Number johomontana@gmail.com I have a Dacor range model number ERD36SBK/LP/H. Do I need to remove the burners to get to the control panel? If so, is the burner ring tool 86007c the appropriate tool to do so?
1 Answer Robert, Yes, the burner ring tool 86007C would be the correct tool to remove the burners on your unit. Read More...
Marvin January 01, 2019 for Model Number dacor sgm304 to diagnose continuous sparking I need to remove the top. Is it correct that to do this all 4 burners must be removed? I see there is a special tool #86007c to remove the ring that holds the burner to the top but I don't understand how to use the tool. The ring holding the burner is very tight. I don't think I would be able to turn the tool by hand. Is this the way to use it or is there another way?
1 Answer Marvin, If you need to use pliers to gently help it will be ok. The continuous sparking would be the spark switches one is closed with the knob in the off position. Read More...
Myfriendhenry November 06, 2018 for Model Number PGM365-1S/NG Is the Dacor 86007C BURNER RING TOOL compatible with the dual burners on this cook-top or do I need another type of tool?
1 Answer Myfriendhenry, The burner ring tool should be able to remove the dual burners for this unit as well as the single burners. Read More...
Martin R February 04, 2018 I have a Thermador PCS366US and I ordered the AP3393645 Burner ring tool. It has the 86007C part number on it. It does not fit my burners. I noticed there is another tool I found | Dacor OEM Part #86007C that looks slightly different. What is the right tool for my unit?
1 Answer Martin, This tool 86007C will be the tool that would work for your dacor unit and would be the same tool as what you located. Read More...
Chuck December 14, 2017 for Model Number ERD30S06CH I have a dacor range # ERD30S06CH I need to get access to the control board that is behind that touchpad screen. I believe I need to remove the burners with the burner tool and the top spill tray to access this. Can you tell me if this is correct and if so, do you have any instructions on what all needs to be removed to access this board?
1 Answer Chuck, On the underside of the control panel there should be screws that hold it in place along with under the knobs. This should allow the control panel to be removed. Read More...