Trish January 05, 2017 for Model Number PLES389ECD I cannot get the self cleaning or broiler to work it shows an error code and shuts off and today I found a part lying inside the oven, it is part number PS1146692 assembly adapter. Can I put the part back in, or do I need a new one? Also could this also be the cause of the self cleaning and broiler not to work? Thanks! Trish
1 Answer Trish, That part could be push and twisted back into place. There should be a thermal cutoff on the back of the range that would have a red reset button. Try pushing the reset and if it trips again would need to be replaced. Read More...
George June 20, 2015 for Model Number FEB27S5DBE Condensate has started dripping pretty bad from the vent on to things in the oven and also has started to come out a little at the door vent . How can I make this stop? Thanks
1 Answer George, This issue would not be caused by the product but would either be that there is not a solid top or bottom of the cabinet installation. Also would want to check to make sure that there is nothing blocking the vent below the control panel or at the bottom of the unit. Also check to make sure that any air vents are not pointed directly towards the unit. This is going to be some type of air flow issue creating the issue. Read More...
Chris May 19, 2015 for Model Number Kenmore Eline 790.47904690 I purchased part #31831700 as the honeycomb fell out of the original and broke when I tried to put it back in place. Turning the old unit did not release it; however, through brute force and lots of twisting and pulling, I got the old adapter out. Looking at both old and new, there do not appear to be any slots that need to be aligned. Instead it appears to simply be a friction fit. Unfortunately, it's a lot of friction such that I can't get it into the vent pipe as more force is needed to try to shove the new unit into the vent pipe than is needed to push the vent pipe upwards into the oven body. Any suggestions on how to install the new one. Will I need to pull the oven out? Will that expose the vent pipe or will I need to remove some of the oven housing to gain access to the vent pipe? Thanks!
1 Answer Chris, To get to the pipe assembly on this unit you would need to pull the unit out and remove the top cover. This will allow access to the pipe assembly. Read More...
Fred December 21, 2014 for Model Number Frigidaire FEF352DSD The ceramic "honeycomb" fell out of the oven vent tube and broke. Your replacement part shows it twists to lock in place. Mine is held in with 2 screws. It came new from Best Buy. Any suggestions? Thanks
1 Answer Fred, I believe you may have the wrong part. Based on the model number given the replacement oven vent tube is part number 316073606. The honeycomb portion is not available separate from the vent tubing. Thanks. Read More...
Mike June 30, 2014 How do you remove the part called "Adapter Assembly" which part number is 318317100 and is part of the "vent" in the oven? Thank you
1 Answer Mike, To remove the adapter assembly you would gain access from inside the oven. You would need to turn it until the slot s line up for it to drop down. Read More...
Jole October 23, 2013 for Model Number PLEB30T8CCB Lower oven not baking or broiling, neither element giving off ANY heat.
1 Answer Hello Jole. Check and see if the thermal switch 318004900 is bad and will need to be replaced on the unit. It has a reset button that you can press and see if the unit starts working properly. If it is good, you will need to check the relay board 318022001 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Shirley J. July 30, 2013 The assembly fell out of my wall oven and a lot of ash continues to fall when the area is touched. Should I clear the area before installing the assembly and can I do this by vacuuming it out?
Struggling To Install July 24, 2013 for Model Number Frigidaire FES367ASF I cannot get the adapter assembly part to push in far enough to twist and lock in place? I am afraid to use force (like a hammer) because I don't want to break the stove. Any thoughts?
1 Answer Hello. Make sure the tabs are aligned properly and the vent tub is not hitting the back side of the adapter 318317100. Read More...
Mark C December 04, 2012 for Model Number not sure but your picture loose the same The center porcelin fell out. What is this part for? Does it have to have it? Is it a safety item if not put in?
1 Answer Hello Mark. This is used to remove the smoke from the oven. You can use the oven without it, but it is not recommended. Read More...
Pete January 30, 2012 Where does this part install at. Mine fell and can't remember where it went in oven. Manual doesn't mention it.
1 Answer Hello Pete. The assembly 318317100 usually installs in the back wall where the vent for the oven is located. Hope this helps. Read More...