Dallace November 25, 2024 for Model Number 790.41013801 Does this part: 316282101 work for either front dual element burner on my stove? My LEFT front dual size burner's inner/smaller element burnt out.
Robert March 25, 2024 for Model Number 79041013800 I have a Kenmore 790.41013800 range. The cooktop has push-button controls on the front and not dials. Both the front elements always say “HE” even when the range/oven is cool and the fan runs constantly as though it’s trying to cool the cooktop off. I read somewhere that the elements have an internal thermometer/thermostat and if this fails, it will do this. However, I can’t tell from the wiring diagram how this would make the fan run continuously, though I suspect it could. Before I spend the money to buy 2 new burners, I wanted to ask for help/advice. The relay board for the range was just replaced.
1 Answer Robert,On the main control board connector J4 check pins 7 and 5, also check pins 7 and 2 for continuity. If they have continuity with a cool cooktop you know the limiter on the element is faulty and needs to be replaced. Read More...
Scott March 24, 2023 for Model Number 79098033800 The front left burner works intermittently. Sometimes it works, sometimes it doesn't. Sometimes only outer half works, but inner doesn't. I replaced the burner 316282101 already but problem persists. I checked wiring too and it's fine. Can you tell me which board on this unit controls this element?
1 Answer Hello Scott, the cooktop elements are controlled by this ESEC board part 316442119. Read More...
Jo October 26, 2021 for Model Number 790.97438402 Will this part replace the right front heating element on a kenmore stove - if it does not fix my issue can I return the part (only outer portion of element is working on the stove - is the element what needs replacing?)
1 Answer Jo, Yes, the correct element would be part number 316282101 for the right front. If only the outer element is coming on then the element would be the issue. Read More...
William Crumpton January 31, 2019 for Model Number 79046703606 will this repace my big element on the right front side of my kenmor stove
1 Answer Hello Joe. You will need to order 318297810 for the element needed for the unit. Thanks. Read More...
Mark December 15, 2014 for Model Number 79046703606 Front 2 burners only heat on high, even when I have it for low setting.
1 Answer Hello Mark. Based on the information you provided, you will need to order and replace the switches for those elements in the unit. Read More...
Mark B May 20, 2013 for Model Number 79046703606 I have a duel element on the stove and only the outer part of the element is working.Do I need to replace the surface element or is it somthing else?
1 Answer Mark, The element is the most likely cause of failure. You can look down through the glass with a flashlight to see if there are any burn marks on the inner part of element. If there are then the element would need to be replaced. Read More...
Debi F. May 11, 2013 for Model Number 790-9802380 What is the dimension of this element? I need a 7" element for my glass top range. Thank you.
1 Answer Debi, the element 316282101 is the dual 9/12" element. The small 6" element is part number 318178110 and the large 9" element is part number 8583165300028. The warming element is part number 140273621015. Thanks! Read More...
Dwayne June 20, 2012 for Model Number 790.4128 one of my elements keeps switching off & on & never allow the pan to get hot enough to even boil water.
1 Answer Dwayne, How much water are you trying to boil, and what burner are you using. Also make sure the bttom of the pot is completely flat. All infinite switches and elements cycle off and on. The more water you're trying to boil, the longer it takes, if the pot bottom is not flat, it's harder to transfer the heat from the element to the pot, from the pot to the water. On average it takes approximately 12 minutes to bring 1 qt. of water to a boil on that style burner. You should try this first, if it takes a lot longer than that to boil, then check and replace the burner infinite switch. Thanks Read More...