Pamela November 20, 2015 We just bought a NG range model number LGGF3043KF. We need to convert to propane. Which part do we order?
Tom November 11, 2015 for Model Number FGFL67HS6 Do I need to adjust the brass fitting for my broiler burner the same way as the oven burner?
Zach October 09, 2015 for Model Number LGGF3042KFR Can you give the part number for LP conversion kit for this range please? The one I thought I need is telling me it's not compatible. I think it is # AP4374168
1 Answer Zach, The correct LP conversion kit for the model number you supplied is GRLP4 / GRLP4. The oven hood orifice(s) should be adjustable. But the kit has the instructions as well. Make sure you label and set the Nat Gas orifices aside (tape them to the back of the range) for future use. Read More...
Jeff October 09, 2015 for Model Number FGF355ASA I purchased LP convertion kit number GRLP3 but my burner cap has the letter S under it with no matching numbers in the instructions. What orifices do I use? Thank You Jeff
1 Answer Hello Jeff. Look at the number on the side of the orifice and match it to the instruction sheet. S may stand for small burner. Read More...
Steve October 06, 2015 for Model Number FAQG7077KA0 Hi I need to convert my dryer back to natural gas. I don't have any if the parts anymore. Could you give me the part numbers and a guide to what needs to be done to go back to natural gas from propane.
1 Answer Steve, To convert the unit back to natural gas then you would need to get the gas valve 5303207409. This is set for natural and would be necessary as the lp to natural kit 134169500 has been discontinued. Read More...
Axtonj August 31, 2015 for Model Number fgf326ase My gas range has four burners that are all the same size. Does this kit have four orfices that are the same size?
1 Answer Axtonj, Yes the lp conversion kit GRLP3 will have the 4 necessary orifices for your unit. Read More...
T. Hunt August 08, 2015 for Model Number FGF348KCJ I have my Frigidaire gas stove with 5 burners on top, they all is work very good. 2 Week from now I have 1 from the right side in the back didn't work anymore, every time when I'm turn it on I need to have the lighter with me. Can someone can help me to find the right part to fixed Frigidaire gas stove Model No.FGF348KCJ Serial No. VF11546292
1 Answer T. Hunt, You will want to check the ignition switch in the light position for continuity. If there is no continuity then the ignition switch will need to be replaced. If the switch checks ok then you will need to check the igniter to make sure that the igniter does not have any cracks or damaged to the insulation. If this checks ok then the issue will be in the spark module which will need to be replaced. Read More...
Kali July 22, 2015 for Model Number FGGF3043KFS Will the GRLP3 (AP4374168) conversion kit work on this model? The 3043 model number was not listed on the cross-reference chart. It has 5 burners with an oblong center burner.
1 Answer Hello Kali. The mode number provided FGGF3043KFS is not showing as a good model. The model number will have to be verified on the units I.D. tag since the one listed came up invalid. This will be necessary to look up and specific parts such as the one you requested. Thank you for your patience and understanding in this matter. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. Here is a link to help you locate it. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Jason June 20, 2015 for Model Number GLGF376DQE I need to convert from LP back to natural gas. What parts are needed?
1 Answer Jason, To convert the unit back to natural gas you will loosen the bake and broil orifices approximately 1 1/2 to 2 turns and close the air shutters on the burner to about 1/4 way open. On the regulator you will flip the cap from LP to NAt. For the top you will need the following orifices: Left front and left rear 316237902, right rear 316237903, and right front 316237900. Read More...
Hayes June 11, 2015 for Model Number Whirlpool ??? I'm trying to convert a 2 burner gas cooktop to LP. The burner sizes are 6000 Btu and 10000 Btu. I know I use a 7mm nut driver to change the orifices. And that I need to convert the regulator. Can you help me find a kit that has the correct orifice sizes? Thanks
1 Answer Hello Hayes, I'm sorry but the LP conversion is model specific and can create a fire, explosion, or personal injury hazard if not done properly. For this reason, we would have to have the model number from the appliance you are converting to give information that will not be dangerous for you. If you could please verify the model number from the units' I.D. tag and we will be able to assist you properly. Thank you for your patience and understanding in this matter. Read More...