Dave January 31, 2014 for Model Number FFHS2611LW0 I'm looking for a bypass filter for this fridge, I have an inline filter on this line already. Will any bypass filter that is compatible with WF3CB (I think) work? Thanks .. Dave
1 Answer Greg, the water filter WF3CB is located in the upper right hand corner of the refrigerator section. Thanks. Read More...
Lyn December 04, 2013 for Model Number FGHS2631PF1 Is there a bypass available for this filter the newer WF3CB?
1 Answer Lyn, the filter bypass for filter part number WF3CB is part number 242294502. However, searching your appliance model number given the replacement filter for your appliance should be part number ULTRAWF which uses bypass plug part number 242294402. Hope this helps you. Thanks! Read More...
Kim October 22, 2013 for Model Number frigidaire refridgerator model #ffhs2322mw2 The newer water filters for my model of Frigidaire...part # WF3CB...now have notches around the rim of the head that prevent it from clicking into the unit. How can I get the older model WF3CB that is smooth around the rim and will fit my fridge.?
1 Answer Hello Kim. The new filter should fit just fine. Make sure you removed the caps from the filter before installing into the unit. Read More...
Gene P. July 01, 2013 for Model Number ffhs2611lb How Do You Tighten Door Handle On Frigidaire Refrigerator
1 Answer Gene, You will need to lift the door handle off with force. Once off you can tighten the screws that are on the door and the screws on the back side of the handle. Slide the handle back in place. Read More...
Dan February 28, 2013 for Model Number Ffhs2611Lqo I removed the water filter by pulling it out. To replace the filter I pushed it in but it will not hold it in . What can I do to get to connect . filter WF3CB
1 Answer Dan, When you push filter in it should click into place and if it is not clicking into place then you will need to replace the filter head. Read More...
Joe Z February 11, 2013 for Model Number ffus2613le4 frigidare How do you change out the water filter?
1 Answer Hello Joe. To replace your PureSource 3TM water filter: It is not necessary to turn the water supply off to change the filter. Be ready to wipe up any small amounts of water released during the filter replacement. 1 Turn Off the ice maker. 2 Remove the filter by pushing on the end/face of the filter. 3 Slide the old water filter cartridge straight out of the housing and discard it. 4 Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing. 5 Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector). 6 Press a drinking glass against the water dispenser while checking for any leaks at the filter housing. Any spurts and sputters that occur as the system purges air out of the dispenser system are normal. 7 After filling one glass of water, continue flushing the system for about four (4) minutes. 8 Turn On the ice maker. 9 Press and hold the Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from “Red” to “Green,” the status has been reset. Read More...
Diann August 19, 2012 for Model Number FFHS2611LBO How do I remove the old filter to replace with a new one?
1 Answer DiAnn, here is the information located in your owners manual on how to change the water filter. Hope this helps! 1. Turn Off the ice maker power switch. 2. Remove the filter by pushing on the end/face of the filter. 3. Slide the old water filter cartridge straight out of the housing and discard it. 4. Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing. 5. Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector). 6. Press a drinking glass against the water dispenser while checking for any leaks at the filter housing. Any spurts and sputters that occur as the system purges air out of the dispenser system are normal. 7. After filling one glass of water, continue flushing the system for about four (4) minutes. 8. Turn On the ice maker. 9. Press and hold the Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from “Red” to “Green,” the status has been reset. Read More...