Nick April 03, 2013 for Model Number 417.83142300 kenmore Is there a lint filter cover that will work with the kenmore 417.83142300 that does not have the sensor? We don't use the auto dry cycle. The cover is physically broken is the reason for replacement. Looking around on the internet I found some that look like it and they were much cheaper I'm assuming because they don't have the sensor but don't want to buy something that won't fit.
Murf April 16, 2012 for Model Number gleq2152es0 Will a code "PL" indicate a failure of this sensor in the AP3790900 unit? The unit starts to run for about 5 seconds, stops, and then the PL code appears.
1 Answer Hello Murf, I checked my resources and was going to send you the fault code list and the owners manual, but my computer doesn't recognize your e-mail address as valid. What I found was no "P" codes at all. Unless it was actually a "PF" which means power failure, I'm not sure about this code. You may want to check the electrical connections, receptacle, junction boxes, and breaker for any possible bad connections. If you want the fault codes, I can still send them to a valid e-mail address. Read More...
Al S April 09, 2012 for Model Number AEQ6000ESO I just asked a question about how the female moisture sensor wire ends connect to the male connectors. Am I understanding right that as long as one wire is connected to the top sensor and the other wire is connected to the bottom sensor, it doesn't matter if they are connected on the same side (top/bottom) or on opposite sides (top to bottom). X----- X OR X------ X OR X X------ Y------ Y Y Y------ Y------ Y THANK. Hopefully, I not confusing you. The above X's and Y's represent the male tongue connectors on the lint filter housing (and connected to the metal sensors on the other side)and the dotted lines the female connector wires coming from inside the dryer body.
1 Answer Al, Your understanding is correct, The moisture sensor circuit is not a polarity sensitive circuit. As long as the two wires are attached to the terminals on the same end of the sensor bar(s) and attached to the wire harness connector properly, you'll be fine. Thanks and Good Luck Read More...
Al S. April 09, 2012 for Model Number AEQ6000ESO I cleaned my filter trap and took off the sensor moisture assembly by removing two screws. I disconnected the two wires which hooked up to the moisture sensor assembly and I forgot which spade, top or bottom, the wire with a white stripe hooks up to. I know which side they hook up to but is the wire with the white stripe on the top or bottom spade connector as you look at the enclosed diagram of part ap2107715: http://www.appliancepartspros.com/Appliance-Parts/frigidaire-sensor---moisture--assembly-w-harness-item-number-ap2107715.aspx Thanks.
1 Answer Hello Al, The sensors are reading resistance from one to the other. It doesn't matter if you hook the wires up to the opposite one or not. It will still read the resistance from one to the other. Read More...
David December 08, 2011 for Model Number 417.49012890 What does this sensor do and what are the symptoms if it goes bad?
1 Answer Hello David. If the sensor 131845801 goes bad, the unit does not work int he auto dry cycles. It can not sense the moisture in the clothes. Hope this helps. Read More...
Brad June 13, 2011 for Model Number sensor (AP2107715) for drier model FSE446RHSO 1. A prior answer instructs the use of a multi-tester to check for proper resistance by wetting the metal bars and touching the leads: is this done with the sensor detached from the drier or still connected (with dryer OFF I assume)? 2. The sensor leads connected to the drier appears well fixed between plastic and metal, not to be easily removed. Does the dryer drum require disassembly to replace the sensor?
1 Answer Hello Brad. You will remove the wiress from the harness. Then put the meter leads into the connectors and wet your finger. Place your finger across the bars, and the meter should read closed for continuity. You will need to remove the front panel to replace the sensor bars. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps.http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
1 Answer Hello Jim, To test this part, set your meter to continuity. Wet your finger and lay it across the two metal bars. It should read closed when the sensor bars make up. Hope this helps. Read More...