Jerry July 20, 2018 for Model Number JVM1540DP1CC Is part number AP4363273 off-white (or bisque)? It sort of looks like it in the picture but doesn't say. That's what I need. Thanks
James November 13, 2017 for Model Number JVM1540DP1WW Does the part come with instructions on the installation?
1 Answer Hello James,As per the service guide, 1. Remove three Phillips screws from the top, front of the cabinet.2. Slide grille to the left and remove.3. Reverse process to re-install grille.4. Remove grille.5. Remove a single Phillips securing control panel. 3. Grasp panel on both sides and lift straight up to disengage four tabs from panel frame.6. The panel is supported by and will pivot on two extended bottom tabs.7. Continue to lift panel vertically to fully remove from frame.8. The re-assembly is in the reverse order. Read More...
Michael September 02, 2015 for Model Number GE JVM-1540DP1WW On the key pad it says service required key pad shorted. Do I need to replace the control panel and or the smart board.
1 Answer Hello Michael. You will need to order and replace part number WB56X10824 on the unit. Read More...
Mike August 06, 2014 for Model Number JVM1540DN1CC Microwave will turn on by itself for 1 minute. Then screen says "keyboard shorted, needs service" . Does that sound like the control panel needs to be replaced? And if so installation seems pretty simple, is that correct? Thanks
1 Answer Hello Mike. Yes, you need to order and replace the keypad. It is not hard. Just make sure you get the ribbon cable installed properly and the power is off doing the repair. Read More...
Bobo July 13, 2014 for Model Number MMV4203DW00 I have a microwave Maytag. When I touch the touch pad ,it will beep then the screen it show only the letter, SE, what does SE means? Nothing works except that message of SE,
1 Answer Hello Bobo. The SE error code is for a bad control panel W10258189 on the unit. Read More...
Robert D. Ii May 23, 2014 for Model Number JVM1540DN1WW My keypad says it is shorted. Do I need to buy the control panel or motherboard?
1 Answer Robert, You'll need the control panel WB56X10824, or at least that's where you need to start. Based on your post information, and the fact that the control panel is more exposed to the environment and usage, it is more susceptible to failure than the control board. Read More...
Gus B. December 24, 2013 for Model Number JVM1540DN1WW I'm trying to take of the Vent Grill so I can replace the key pad. I have only found 2 Screws in the top of the Grill, Grill still won't come off. What am I missing?? I have tried prying but don't want to break the Grill.
1 Answer Hello Gus! When the two screws are removed, the grille will slide to the left and unhook from the microwave front. Hope this helps you, thanks. Read More...
Colin November 17, 2013 for Model Number WB56X10824 I need to replace the control panel on my microwave. Does this panel snap on in some manner or is it secured with screws that i cannot see without dismantling the whole cover assembly?
1 Answer Colin, To remove the control panel to replace it you would need to remove 3 screws at the top of the microwave that holds the vent grill in place. Once the screws are removed you will then remove the grill. There will be a screw holding the control panel in place remove the screw and lift and pull out. Read More...
Mary B September 11, 2013 for Model Number jvm1540dn1ww ge microwave The keypad on my Mom's microwave no longer works. Only the 30 sec. button works. Would replacing the Assembly Control Panel fix the problem?
1 Answer Hello Mary. Yes, you will need to order and replace the control panel WB56X10824. Read More...
Eliza September 09, 2013 for Model Number jVM1540DN188 My microwave surface light is stuck on. It still makes the beep when you press the keypads on the front, but it has no affect on the light, it just stays on. Do I need a new PCB?
1 Answer Hello Eliza. Based on the information you provided, you will need to replace the smart board WB27X10934 in the unit. Read More...