Robert November 19, 2022 for Model Number JGRS14BEW Hello, I keep getting error codes f3 and f4 on my older Kenmore 24" gas wall oven with bottom gas broiler drawer, I replaced the temp probe twice and it still does it, I think it might be the circuit board, what circuit board # does this model have in it, the only model number I see on the back of this oven is JGRS14BEW no other numbers are on the back of the oven.
1 Answer Robert, the wires going to the temperature sensor would need to be inspected for any crimped or broken sections. If the wires check good, the oven control WB27T10268 would be the cause of failure. Unfortunately, the control has been discontinued by the manufacturer and is no longer available. Read More...
Chris G February 23, 2016 for Model Number kenmore 911.3022190 I want to know if this is the part i need to get. My oven will not lite, i checked the ignitor/glow bar and it has continuity (350ohms or so) I also used the Technical Data Sheet to test the Electronic Control it says the voltage test- relay contact operation should be L to N 120vac all times ,L to BA 120vac unit off, and L to BA 0 vac bake/broil. I have found when probing at the connection with the wires connected that i have L to BA 120vac all the time, when i turn the unit on it dose not change to 0vac. Am i testing this correctly and would this indicate that i need a new control unit I also do not hear any click from the relay in the K2 spot when i power on of off the oven. the controller is a GE WB27K5056 thanks so much, looking forward to get this thing fired up!! Chris
1 Answer Chris, This is the correct testing to do and it does sound like the control board WB27T10327 would be the part required to replace. Read More...
Ezed. December 06, 2014 for Model Number wb27k5056 Is there a schematic diagram showing how to place the connectors onto the TIME CONTROLS? I removed them all before I received the new one to match them up, if so how can I get a copy?
1 Answer Hello EZed. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
1 Answer Hello Scott, If I understand what you are needing correctly, it is as follows: PR to Br terminal PR=purple BK to L1 terminal BK=black Y to Ba terminal Y=yellow R to C terminal R=red BK to NO terminal BK=black W to N terminal W=white And the multi-wire connector to the connection on the end. This is for the self clean model. For the non-self clean model: The connector with two white wires goes to the oven sensor terminal marked 3,2,1. The BK wire goes to the L terminal BK=black The O wire goes to the BA terminal O=orange The W wire goes to the N terminal W=white The GN wire goes to the GND terminal GN=green Read More...
John W. July 03, 2012 for Model Number JBP22GE1AD Does GE still make a clock control board for this range oven?
1 Answer Hello John. No, The clock has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Renato December 04, 2011 for Model Number JGRS14GEP1BG Is the control board of your 2BG the same with 1BG?
1 Answer Renato, The ERC/Clock is WB27T10327 It has been re configured by the manufacturer to operate on all versions of the product you have.Good Luck and Thanks Read More...
Gerald November 25, 2011 for Model Number JGRS14GE2BG Found all answers to installing a WB27T10327 clock except 2. Where does the orange wire from the BR spade go? And the extra black wire with the kit? Your answer to another person was, "connect from the L1 to the 'com'.There is no com spade on the new clock. Also there is no 'NO' spade for the BR to go to. There is a 'Broil' spade on a relay and a second spade marked L1A on the same relay.
1 Answer Hi Gerald. The green wire from the "GND" terminal on the old board goes to the "GND" terminal on the new board.The pink wire from the "BA" terminal on the old board goes to the "NO" relay terminal on the new board.The black wire from the "L1" terminal on the old board goes to the "L1" terminal on the new board.The white wire from "N" terminal on the old board goes to the "N" terminal on the new board. The green wire from the "GND" terminal on the old board goes to the "GND" terminal on the new board.The pink wire from the "BA" terminal on the old board goes to the "NO" relay terminal on the new board.You have to cut off the two yellow wires from the 3 pin old plug. These wires should be spliced with the two white wires (pin 4 & 6) from the plug supplied with the new board. All other wires from this plug should be insulated. Thank You. Read More...
Roger L. August 22, 2011 for Model Number jgrs14gep2bg I just bought this part from you. How do I install this part in my GE oven? Where do I hook up the wires. This part is a newer one than the old one I had.
1 Answer Hello Roger! This answer was located on our Repair Forum, this is a free service in which technicians will assist with answering repair questions for our customers. Please use this link to assist in your repair. Hope it helps, thanks!http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/15487-oven-control-erc.html Read More...