Nancy March 18, 2024 for Model Number JS968BK5BB Code 43 comes up... door locks.. does that mean I need a new control board If i get a new control board is it hard to put in or does a repairman have to do that...
1 Answer Nancy,Check the temp sensor for 1090 ohms at room temp. The door should only lock in a clean cycle or extreme temp so if the sensor is out of spec the unit may think it is to hot and lock for safety. Otherwise the control would probably need replaced. Replacement would depend on skill level. If your uncomfortable let a service tech do the job. Read More...
Richard May 07, 2019 for Model Number JS968SK5SS The range was working and then I moved it to a different house where I wired the power connections to the range incorrectly. Realized the mistake and reset the connections. The top of the range is fine, but the oven doesn't do anything - no lights at all on the Control ERC. Do I simply need to replace the ERC, is it something else, or multiple problems that I created?
1 Answer Richard, If you wired the unit wrong and plugged the unit in, then there is no display then the control board would be faulty and need to be replaced. Read More...
David February 17, 2019 for Model Number GE PROFILE RANGE J S968S K5SS Oven will not turn on for any selection. Error code is LOC 0 when pressing any selection for the oven. After several seconds display returns to clock time. Oven selection for 'self cleaning" shows "LOC 0" for several seconds and then returns to clock time. Range works fine. Are there any other parts to change other than the Range oven control, PART NUMBER: WB27T10803?
1 Answer David, you may want to check to see if the control was placed into locked mode. You can do this by pressing and holding 9 and 0 at the same time for three seconds. When three seconds pass, you should see LOC OFF flash on the screen. If this occurs, it was just set to control lock. If it does not unlock the control, then you would be looking at changing the oven control. Read More...
Chimp April 13, 2015 for Model Number JS968BK3BB Oven will not heat. Broiler Works. Heating elements pass tests, and do not indicate any problems. When the touchpad is used to set the temperature, all indicators and visible readouts do not show any signs of trouble. But, the oven will simply not heat. I think it's the relay switch on the ERC, but hesitant to drop over $200 without knowing for sure.
1 Answer Chimp, If the oven bake element is checking ok, then check the wiring between the bake and the oven control to make sure that there is no damaged wires. If the wiring checks ok then the oven control WB27T10803 would be the issue. Read More...
Guy P July 08, 2014 for Model Number JSP46WOD1WW The oven will not heat in bake, broil, or clean. The touch pad does indicate that I have set the temp to 350° so it thinks it is turning on but no relays make noise. Do I need a new Control ERC? Thanks, Guy
1 Answer Hello Guy. If there is power tot he board, but nothing from the relays, you will need to replace the control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Bob April 13, 2014 for Model Number GE JS968TOF6WW Glasstop range, conv./std oven. Conv. oven works fine. Standard oven sometimes does not heat unless first set on convection, & when it starts heating, switch over to regular. The heat on a couple of the burners either slow to heat up and/or then once they do, won't reduce heat when put on lower setting. Is this just a bad ERC or something else? P.S. no error codes. Thanks
1 Answer Hello Bob. Yes, based on the information you provided, it sounds like the ERC is bad and will need to be replaced in the unit. Read More...
Brian December 19, 2012 for Model Number Ge Profile JD968TK4WW The buttons do not respond for oven control, nothing happens when buttons are pushed, replaced glass control panel, that did not correct the problem will this ERC be the problem??
1 Answer Hello Brian, Based on you changing the touchpad, you would either need to replace the harness WB18T10386 or the ERC WB27T10803. You may want to double check all connections and check wires to ensure that they are not faulty. Read More...
Mary January 05, 2012 for Model Number JS968SOK4SS Oven shuts off after pre-heating in all cook modes. Are there any other parts that need to be replaced beside the Oven control Erc? or will this part remedy the situation? Thanks!
1 Answer Hello Mary. Based on the information you provided, it sounds like the ERC control WB27T10803 is bad and will need to be replaced. If the oven preheats properly, and the temperature inside the oven is correct, you will need to replace the ERC. Hope this helps. Read More...