Karen June 30, 2022 for Model Number DPGT750GC2PL Profile Gas Dryer bought new has always had issue of turning itself off during drying cycle. Sometimes it does this a few seconds after start, sometimes not for minutes, sometimes turns off many times, sometimes just once or twice, sometimes not at all. It always starts again after I open and close door. Is this a timer problem? Do I need to replace WE04x10107 or would you diagnose something else? Thank you for speediest possible response.
1 Answer Karen, based on the information provided, it is very likely that the main control WE04X10107 has failed if the duct of the dryer is clear and has proper airflow to the outside of the house. Unfortunately, the control has been discontinued by the manufacturer and is no longer available. Read More...
Carl October 14, 2018 for Model Number DPGT750EC2PL The buttons on the dryer do not work. The touch screen does and appears to be ok. However, can't do anymore as the start/stop button doesn't work. Also can't run through any diagnostics as the buttons are needed. I have checked the button with my meter and they seem to work correctly. I have checked power to the board and it is reading correctly. The next test is for the power to the membrane and LCD. They only way to check is remove the harness. I get no voltage there. This seems odd as it is power to both and one works. Must the harness be attached for this test to work correctly? Also, the next test asked for the LCD to be running but I can't get any reading with my meter as they are too large to get to the wire in the harness. Also, if the board is bad, it is no longer available. Do you know of any method or company to fix?
1 Answer Carl,You can test the user interface harness if you have a key supplied by the manufacturer reading ohms between 2 points on the membrane when a certain button is pressed. Unfortunately, we do not have the key but it could be in your tech sheet that came with the dryer. If none of your keys are shorted then the problem would lie somewhere else. So you wouldn't need the user interface membrane connected to test. Read More...
Doug P January 06, 2017 for Model Number GE Harmony mod # DPGT750GC1WW My GE harmony dryer display does not lite up as if there was no power to the dryer. I have checked and there is power going to the pwr/pcb asm-main board p/n WE0410107, and it seems like there is power going to the touch display assembly power/lcd p/n WE04X10105. I get a power reading with a volt meter at both, but still no display on the touch pad. I'm sure that that either the pwr/pcb asm-main board or the touch pad display assembly power/lcd are bad. Any suggestion? Should I try replacing the touch pad first since it seems to have power coming from the main board? Thanks.
1 Answer Doug, Yes if there is power going to the touchpad then you will want to replace this first. Part number for the display is WE04X10134. Read More...
Glenn September 17, 2015 for Model Number DPGT750GC1PL When room is below 75°F, dryer is totally dead no power except door light will come on. No display no clicking nothing. If I warm up the room to 85°F, the dryer works perfectly! I changed the thermistor on the blower housing and checked the thermostat but I still have the same problem. I will order the board if you think it's the problem, but I don't want to spend close to $300.00 for it if it doesn't correct the issue. Thanks
1 Answer Hello Glenn, This sounds like a possible cold solder joint on the board WE04X10107. Read More...
Maria July 17, 2012 for Model Number UDPGT750GC1P GE/HOTPOINT GAS DRYER If we buy Item Number AP3794590 (electronic circuit board) from you, will we ourselves be able to install it, or are we going to need a GE technician?
1 Answer Hello Maria, Discontinue the power supply to the unit before you start. Now remove the control panel and the board is under it. Once you get this far, the most important thing I can tell you is to remove one wire and install it on the new controller. Remove the next wire and install it on the new controller. Continue with this procedure until all wires have been transferred to the new part. Re-assemble in reverse order. DPGT750GC1PL Read More...
George April 23, 2012 for Model Number dpgt750gc0ww My screen shows the message model connection problem. In order to repair it do I need to order a new main power board?
1 Answer Hi George. I would use the digital capacitor Tester / Volt/ohm meter part # MA-DM1 to assist you in repair. Screen will display "Serial communication link between the washer and dryer is down. Please check for proper connection, the dryer is plugged in,or board input /output signals". The washer sends a signal back to the dryer acknowledging receipt of information. An error is set if the dryer has not received a proper response from the washer after 3- attempts. 1.) Check options to insure communications feature is selected or 2.) Wiring connections or 3.) Serial cable or 4.) Internal washer or dryer cable or 5.) Main Control board part # WE04X10107. Thank You. Read More...
Adrian A. December 18, 2011 for Model Number GE GAS DRYER DPGT750GC1PL Display is dead no sound. Only the inside drum light is on. I checked the fuse on the control panel and is ok. Please advise.
1 Answer Hi Adrian. The main control board is part # WE04X10107. This is the brain to the unit. It is mounted behind the control panel. Remove the back cover and remove the top cover to the board. Inspect to see if there is the fuse open or the board circuit burnt. Thank You. Read More...
David March 24, 2011 for Model Number GE DPGT750 gas dryer Tested all heat sensors with ohm meter and they check out ok. The blower motor won't go and no heat. Any ideas? One repair man said it had to be control board??
1 Answer Hello David. Test the blower motor and see if your getting power to it. If there is power to it, you may have a bad motor. Hope this helps. Read More...
David March 23, 2011 for Model Number gas dpgt750 Is there a way that this can be tested to make sure it is the problem?
1 Answer Hello David. You can test and see if you have power coming into the board, and power going out of the board. If there is power coming into the board, but not out of it, the board is bad. Hope this helps. Read More...