Darnell September 10, 2014 for Model Number JVB98H1SS When pressing the raise/lower switch on my JVB98HSS I get no response whatsoever. No sound, no movement, no nothing. The vent is in the down position. I put a multimeter on the outlet and there is full power. I disconnected the Switch Membrane from the Lead Wire Jumper and the Lead Wire Jumper indicates power. What are my resolution options? Could the problem be the Switch Membrane? Please advise.
1 Answer Darnell, You can test to make sure that there is 12 vdc getting to membrane. If it is then the membrane is faulty. The most likely cause for the issue will be the raise/lower control board WB27X10704. Read More...
Bobr June 12, 2014 for Model Number JVB37A3WW Hello. I bought this part #WB24X10114 to replace a switch that went bad, but the old switch did not have the same plug as on this one. In fact, I did not see any plug only wires attached to the switch that ran down into the cavity. Unless the plug for the switch is way down in the cavity? In that case, the short wire on the new switch will never reach. Do you have any suggestions? Can I buy a female plug for the new switch?
1 Answer Bob, The membrane switch goes to the power board which can be accessed from the back of the unit. Read More...
Scott August 01, 2013 for Model Number JVB67H1BB I replaced the switch membrane because it shorted out when I spilled water on the counter top. the switch membrane plastic casing wore out and the water touched the bare wire. The new switch will not operate the lift. There is power at the outlet. I am wondering if another part went bad when the water caused a short circuit. Scott
1 Answer Hello Scott, The unit has a power control board (AP3202875) which was most likely damaged when the harness was shorted by the spill. Read More...
Kb March 20, 2013 for Model Number ZVB36SH1SS We have a 36 inch GE Model ZVB36SH1SS. When lowering the unit it got stuck on a box. I removed the box and the vent slammed down and now the motor just keeps running like it is trying to lower it. The fan isn't blowing but you have to unplug the unit to keep the motor from running. The unit won't budge when trying to lift it up as it seems jammed. Any suggestions? Thanks, KB
1 Answer Hello KB. It sounds like the switches are not contacting and the ram is broken. This will need to be disassembled to determine which part is broken in the unit. Also, test the switches on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Dean L. February 02, 2013 for Model Number Jvb37h1bb My GE telescoping downdraft is stuck in the UP position. The fan still works. I'm not really sure where to start. Any suggestions?
1 Answer Hello Dean, You will either have a bad start switch, a bad limit switch, a bad relay board or a bad motor. If you have a test meter, you can test these components. The tech sheet should be in an envelope or a sticker on the blower housing under the cabinet. This will guide you through the circuits. If you hear the unit trying to operate, you probably have a bad pivot arm. Read More...
Blake January 15, 2013 for Model Number WB24X10115 My downdraft fan will not raise or lower. Assuming it is the switch. How can I check this? If the touch pad...do you have instructions to install?
1 Answer Hello Blake, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Mike December 30, 2012 for Model Number ge profile downdraft jvb37h1bb I pryed off the decorative trim and unplugged the switch. The female end of the switch plug is down about 3 or 4 inches and the access way is only about an inch square. The female end is not fixed so it must be held in place while plugging in the male end of the new switch. It seems like a couple pairs of long needle nose pliers is the only way, but with only a square inch access area, it is crowded and not possible to see. Is there a trick to plugging in this new switch? Thanks, Mike
1 Answer Hello Mike, It's been a while since I last serviced one of these, but if I remember correctly, the snorkel was in the down position. I removed the cook top and set it on the edge of the counter top to allow room to remove the gear motor panel and access was greatly simplified. This was quite a lot more work since it was a gas unit and I had to disconnect the gas line but, in the long run, it was much easier than trying to connect the two without being able to see or physically touch either connector. Read More...
Fred October 23, 2012 for Model Number JVB94SH1SS We have a GE Profile down draft unit. We were having trouble with the fan speed switch, it sometimes would not work-no fan at all. Now, we can't raise the unit at all! I realize there are several switches that to consider, but which one? I would hate to buy all of them just to find out! Any help?
1 Answer Hello Fred, I would try try the variable speed switch WB24X10035 since you were having trouble with it anyway. We have a one year warranty and one year return policy so there is no risk for you. Hope this helps! Read More...
Holly October 12, 2011 Our G.E. vent does not have the jumper box. Our switch that makes the vent move up and down is already installed on the unit and has a ribbon cable thar runs from the switch directly to the motor. The switch is shorting but the motor still runs and we need to cut the ribbon cable to install a new switch without replacing the entire switch and motor. Any advise? Only the 36 inch vent has the switch with the jumper box that you can remove and replace.
1 Answer Hi Holly. The jumper lead is part # AP3205966. Thank you.Read more: http://www.appliancepartspros.com/Appliance-Parts/ge-switch-membrane-blk-item-number-ap3203483.aspx#ixzz1afbhDI4M'>http://www.appliancepartspros.com/Appliance-Parts/ge-switch-membrane-blk-item-number-ap3203483.aspx#ixzz1afbhDI4M http://www.appliancepartspros.com Read More...
Holly M. October 10, 2011 for Model Number Jvb37h1bb The touchpad switch that you carry plugs in but ours travels back to the unit. Is there a way to connect the two? Do we need a special tool?