Bill February 01, 2021 for Model Number DLB3800SBLWH The dryer heat works sometimes, but not others. I pulled it apart and checked the heating coil and the thermostats with an ohms meter. (It has 5 different thermostats! 3 in heating element housing and 2 up front) They all have continuity. I also found a lot of lint built up around the front 2 thermostats and throughout the duct work. I thought this was my problem. Thoroughly cleaned all the ductwork, fan, and thermostat area and reassembled. It still only works sometimes. I can start it and hold the door switch in and see the element heat up sometimes. I laid a thermometer in the lint tray and it got hot when working, on high about 160, on low I think 125. When I start the dryer I will wait a few minutes and feel the exhaust duct. Sometimes it is warm, sometimes no. And sometimes when it is warm, I'll check it again later and it's cold. Sometimes clothes drying in one cycle, other times have to run it 3 times. Not sure how to test other than with the unit off and with an ohms meter. Any help would be very appreciated. Bill Wolfe wtwolfe@att.net
1 Answer Hello Bill,if you have checked the heater element and the thermostats and are reading continuity with no loose wiring terminal connections or signs of overheating, next check the wiring (L2 circuit) at the motor switch wiring connections for the same signs, if ok there may be a problem in the timer. Read More...
Helen September 12, 2019 I HAVE A WHIRLPOOL (ROPER) DRYER WAS DRYING CLOTHES IT SHUT DOWN AND NOW IT IS LIKE THERE IS NO POWER TO DRYER. WONT COME ON, ETC. WE CHECKED BREAKER ITS GOOD, UNPLUGGED DRYER PLUGGED BACK IN STILL WON'T START
1 Answer Hello Helen,if you would repost your question with the dryer's model number we would be able to use the dryer's wiring diagram to help you repair the dryer. Read More...
Brenda H October 21, 2018 for Model Number DDE7100NCL WH Hi I have General Electric Dryer and I bought part numberWE4X800 T-Stat Safety Switch. I just took my dryer apart and it has a different switch in it but there is a spot up from other switch on my dryer were the WE4X800 would fit so I was wondering if I could the WE4X800 t-Stat Safety switch instead. Thanks
1 Answer Brenda, You would want to use the thermostat that goes to the unit as they are designed to operate at different temps per the manufacturers specifications. Read More...
Greg March 16, 2018 Have an old GE Dryer not sure of the model(GE Heavy Duty Automatic Dryer. The Dryer seems to be Overheating, Looking inside i can see the element going off and on, not shorted to chassis, clothes comes out very Wriinkle. what is the purpose of the sensor on the Doord
1 Answer Greg, We're not aware of any dryer with a sensor in the door. But wrinkling of clothes is usually due to excessive heat and/or time. Your first check should be in the exhaust vent pipes and vent hood, outside. Lint and debris in the venting or a collapsed /damaged vent hood, would restrict the air flow and cause the dryer to overheat in the dryer drum and cause the clothes to wrinkle. If you can get us a model number, it would be very helpful. Thanks, Read More...
Ark June 04, 2014 for Model Number dcl333eaoww I am seeing this part can be used in place of the stock thermal limiter switch #we25x1011 just the switch not the new GE kit, is this correct?
1 Answer Ark, the thermostat in the kit you will need to use part number WE04X10094. Thanks! Read More...
Bryan January 10, 2012 for Model Number nvlr333evoww Would this part fix my no heat problem? Or it is the timer switch/resistor? I already replace the heating elements. I get 0 ohm(s) for the thermostats, which is good from my understanding. I get the same reading from the "cabinet and top" thermostats. Thank you!
1 Answer Hello Bryan. Yes, if the safety thermostat WE4X800 is open, it will prevent the unit from heating. Hope this helps. Read More...