Tinyjmartin November 19, 2023 for Model Number WSXH208F0WW washer runs through cycles until it gets to final spin . it never goes to end cycle. if I don`t watch the load it will spin for an hour and never shut off. I have to advance control to finalize and unlock tthe door.
1 Answer tinyjmartin,Based on the information provided this is the timer for your model - WH12X10152 Read More...
Karen November 30, 2021 for Model Number WSXH208A1WW The washer will fill and initially tumble (also washes through dispenser properly) but fails to progress through the cycle. I can manually go to each cycle (tumble, drain, spin, fill, drain, spin, fill, drain, spin) with the timer and each will NOT advance on it's own. It does what it needs to do and stops. WE HAVE REPLACED THE TIMER SWITCH ALREADY with part number AP2620106. Any suggestions with what we should try next? Thanks
1 Answer Karen, based on the information provided, the speed control WH12X10154 is not providing neutral during operation to the timer when the timer motor cam 6 is open. This would mean that the speed control would need to be replaced. Unfortunately, this part has been discontinued by the manufacturer and is no longer available. Read More...
Kevin November 25, 2016 for Model Number GE WSXH208H1WW The washer in any cycle only shows the door locked light. The door is not locked (no clicking) so, no other action happens.
1 Answer Hello Kevin. It sounds like the door lock assembly WH10X27534 will need to be replaced on the unit. Read More...
Tom July 31, 2015 for Model Number wsxh208h1ww This GE front load washer model #wsxh208h1ww wash will not do anything in any cycle only the lock light comes on and stays on solid.
1 Answer Tom, If the unit just locks but will do nothing else then you will want to check the water valve to make sure that the screens are not clogged and make sure that they are getting 120 vac to them. If they are not getting power and filling the washer then the timer would most likely be the issue. If they are getting power then the issue will be the water valve causing the issue. Read More...
Forrest February 15, 2013 for Model Number wsxh208foww The washer fills but the motor does not agitate or spin it appears to be the timer not moving.
1 Answer Hello Forrest, You will want to check your lid switch. If the lid switch shows open with the lid closed then the switch is bad and needs to be replaced. Read More...
Glen December 17, 2012 for Model Number WSXH208H3WW Our front loading GE WSXH208H3WW clicks and advanced through filling and draining very quickly and never spins at any point. Does this sound like a timer issue to you? Thanks!
1 Answer Hello Glen. Yes, if the timer advances fast and does not operate properly, you will need to order and replace the timer WH12X10152 on the unit. Read More...
Etch October 01, 2012 for Model Number wsxh208a1ww My GE front loading washer wsxh208a1ww is taking at least 7 hours to complete a wash cycle (normal is about 1.5 hrs or less). It would start normal and fill water in the tub, spin a normal for a little while and then at certain point, it would just halt and idle without progressing. The motor seems to spin at normal speed if it spins and the water fills and drains normal. It's just that it wouldn't progress the cycle at a normal speed. We can push in the knob and help it progress, but it would halt and idel after a short while and then takes a long time to complete the cycle. Does this sound like a time controller problem? Is it easy to replace?
1 Answer Hi. Anytime you need to advance the timer manually then it is tine for the timer replacement part # WH12X10152. Throw 5 or 6 towels in the washer with no soap and let it run for a few minutes. If there is any suds, advance the unit into drain and get rid of the suds. Keep filling the unit with cold water and immediately drain over and over until clear. This will cavitate the pump and overheat it,causing it to pause and allow the pump to cool down. Thank You Read More...
Nelson April 26, 2012 for Model Number wsxh208a1ww Washer fills but wont do anything after, just sits. If I advance the timer still the same, but if I go to final spin it will spin and not stop. Is this the timer that is bad ?
Brian November 04, 2011 for Model Number WSXH208A1WW The washer will go through its normal tumble cycle but will not spin out at the end. I was wondering if there is an obvious mode of failure for this problem or if I can at least get an electrical schematic for my model.
1 Answer Hello Brian. Check and make sure the pump is clear and is not clogged. If it is good, then you will need to check and see if the door lock WH10X27534 is bad. If so, it will cause the problem you are having. Hope this helps. Read More...
Joseph K. July 23, 2011 for Model Number WSXH208F0WW My front load washer was vibrating, walking and would not stop. Could this have been caused by a bad timer. The shocks appear to be okay. I took the timer out and reinstalled it. It was pretty banged up. However the machine started off good, I advanced the timer manually once but at the end the door would not unlock until I unpluged the machine.
1 Answer Hello Joseph. Based on the information you provided, it sounds like the shocks WH17X10001 are weak and is causing the unit to vibrate. Check and make sure the tub bearing is good in the unit. The timer WH12X10152 does not control the vibration of the unit. Hope this helps. Read More...