Marc October 01, 2025 for Model Number GTW720BSN0WS Lid lock was cycling, machine didn’t recognize it was engaging. Replaced the lid lock kit and it worked for a couple washes, and now it’s doing the same thing again.
1 Answer Marc, This issue will most likely be with the control board. It would be recommended to check for error codes first though and you would want to get the tech sheet and put the unit into service diagnostics and see if there are any stored errors. Read More...
John July 13, 2025 for Model Number gtw725bsn0ws i have a waher that when power buttin pushed on then lights u0 for 3 sec and shots off found water spry on control bords so can you give price on the 3 bords under cover and the watter cellinoid velve
1 Answer John, Thank you for your question. The control boards in the console will be part number WH22X29049 Inverter, WH22X36477 Main Control Board, and the valve WH13X26637. Read More...
Dp December 20, 2024 for Model Number GTW720BSN0WS Washer controls are lighting up but power button ia not working. The wash options keeps changing automatically. Do i need to replace main board? Can i find used main board at cheaper cost?
1 Answer Hello DP, thank you for contacting Appliance Parts Pros.Yes, the main control board WH22X36477 WH22X36477 will need to be replaced. We do not recommend utilizing used components for repair. Read More...
Susan November 04, 2024 for Model Number GTW720BSN1Ws My washer stopped spinning on the final rinse/spin. It washes, just not a final spin. Hoses were checked and clear. Had a tech out today and naturally it worked for him. Would this sadly be a motherboard issue possibly? Thanks
1 Answer Susan, Check to ensure it is not a suds build-up or the use of too much detergent...before condemning the board. Read More...
Scott June 14, 2024 for Model Number GTW725BSN0WS Initially my lid lock broke and it stated the lid was open when it was not. I purchased a new lock assembly, but the solenoid for the lock is not activating. I tore apart the old lock assembly and I'm able to make the machine work by holding the one switch for it to indicate lid closed. The other I have to actuate when the machine is expecting the lid to be locked. Then the motor will start. I confirmed continuity on all three wires of the lid lock harness, so I don't believe that is my issue. Is there a fuse for powering the lid lock solenoid or am I needed to replace the main control board?
1 Answer Scott, if the lid strike WH08X37938 has not been damaged and properly actuates the new lid lock, the most likely failure would be the main control WH22X36477. Read More...
Mike May 19, 2023 for Model Number GTW725BSN1WS One of the relays fell off the board am I able to solder it back on the board so that my washer will work again?
1 Answer Mike, it would be recommended that the control is replaced as the relay falling off can cause more failures within the control. Read More...
Lee May 19, 2023 for Model Number GTW720BSN1WS Are there instructions on how to install the board on my washer?
1 Answer Lee, with the power cord unplugged, the knob, console back panel, and rear mounting screws would need to be removed. This will allow the console to lift up so that the control WH22X36477 mounting screws can be removed. The wires would then be switched over to the new control one at a time and the new control installed. Read More...
Mike May 19, 2023 for Model Number GTW720BSN1WS My washer is filling and then draining but it will not wash or spin. I am getting a error code 25 will replacing the board get y washer back up and running?
1 Answer Mike, This error code will be a pressure switch getting incorrect signals and here are the things to check. Check to make sure that the house water supply valves are turned on. Check the water valve operation. Check for proper drain pipe and stand pipe height. Check the pressure tube for pinches where it goes through the top cover grommet. Use pressure sensor test 10 to ensure correct pressure sensor operation. Check the pressure tube for trapped water. Ensure the pressure chamber port is free from obstruction using drill bit size 1/16" by hand so as not to drill through the inner wall. Read More...