Steven February 22, 2022 for Model Number 79571033010 Top circuit board is clicking. The refrigerator is staying cold but the freezer is not.
1 Answer Hello Steven, on the rear cabinet under the cover the smaller board powers the compressor, check if the LED indicator light is flashing and if so count the flashes, it indicates what the problem may be. If it is on steady, run the Diagnostic self-test by holding Frez and Fridge keypads for 6 sec then release and record the code if any. Read More...
Marcio February 24, 2021 for Model Number LG model lfx25978sw/00 The compressor of my refrigerator stopped fan continues to run and I hear repetitive click sounds on the PCB board EAX61745402 would this board be the problem?
1 Answer Marcio, This unit has an inverter board on it and this would be the most likely cause which is part number EBR64173902. Read More...
Bill Smith October 29, 2020 for Model Number Kenmore Elite Model 795.71039.010 My refr4igerator and freezer are not cooling. There is a clicking noise coming from the upper PCB board.
1 Answer Bill, For this issue, the most likely cause of the clicking noise will be a faulty main control board EBR65002706. Read More...
Bill June 16, 2020 for Model Number 795.71053.010 Hello, I have a malfunction with both the frig and freezer not cooling frig temp 56 and freezer 48 degrees. Compressor seems to be running continuously, all three fans are running and there is zero frost buildup on the evaporator. I have replaced the thermistor and temp sensor also the mainboard, not the PCB. The compressor is running at 100 degrees and the coil is at 74 degrees. Not sure if the other board should be replaced or maybe the control panel. I don't think the freon is low because there is no ice buildup anywhere.
1 Answer Bill, it would be recommended that the condenser coils are inspected for dust build up as dust can cause this symptom. If the condenser coils are clean, then there is a sealed system failure based on the information provided. Read More...
Suzie September 05, 2018 for Model Number lmxs30796D The instaview door light keeps coming on with any slight sound in the house. Wondering if it's a sensor or a faulty board.
1 Answer Suzie, There is a knock on sensor that would be the most likely cause for this issue. The part number for this would be ACQ88646104 and should be located at the bottom of the door. Read More...
Ajf August 16, 2018 for Model Number 79571033010 First noticed food thawing in freezer section, and checked temp with a thermometer. Compressor runs temp was reading 40 in freezer and 45 in upper . Did not feel air flow to upper compartment . Fans. Don’t seem to be running. No ice or frosting on evaporator . Almost seems like stuck in auto defrost . What could be the cause ?
1 Answer AJF, if your compressor is running you should have a frost pattern on the evaporator. It sounds like you have a sealed system issue, it is either low on freon or the compressor is failing. Read More...
Willis August 25, 2017 for Model Number 79571072010 Top circuit board is making a clicking noise. The fan for the condenser runs but the condenser doesn't kick on.
1 Answer Willis, This issue would most likely be caused by a the control board being faulty which would be part number EBR64173902. Read More...
J September 25, 2016 for Model Number 795.71059.010 kenmore elite refrigerator Refrigerator not cooling, no errors. Compressor was not running, condenser, evaporator fans running. Changed compressor start cap, now compressor runs not cooling. Checked voltage out of compressor driver (PWB assembly) 100 vac most of the time, briefly goes to 200 vac sometimes and 430 vac sometimes. Is it bad E-Inverter FC75LANE?
1 Answer J, If the compressor is running but the unit is not cooling at all then this would be a sealed system issue in which you will need to have a service technician to repair. Read More...
Stillwater May 31, 2016 for Model Number lfx28978st Compressor will not start control board on back part number ebr64173902 will then blink 2 times repeatedly does this mean something. Before I had a compressor put on it would blink 7 times.
1 Answer Hello Stillwater. You will need to check the compressor harness on the unit. If it is good, then the compressor will need to be replaced. Read More...
David September 10, 2014 for Model Number Kenmore # 795.71053.010 The compressor does not run, has no power to it. No burnt signs or bad fuses either board. Which one is most likely bad, or is there some way to test boards ? Thanks
1 Answer David, Unfortunately we do not have a wiring diagram for the unit to be able to give voltage information for the unit. You will want to test the PCB sub assembly for proper power. With the compressor not getting power then it is most likely that the PCB Sub Assy EBR64173902 would be the issue with the unit. Read More...