Chris Rice June 04, 2023 for Model Number Samsung wf350anw/xaa Power on/off button is intermittent/inconsistent. Sometimes you have to push it on top/bottom, sometimes on the right or left, or in the center. Not sure if that is the SAM-DC97-16052A assembly or the control board. Any advice on what needs to be replaced? Thank you!
1 Answer Chris, This issue would most likely be caused by the button assembly part number DC97-16052A. Read More...
Bob February 14, 2022 for Model Number WF350ANW/XAA I bought a new PCB Main DC92-00381A and received it today. I exchanged the parts one plug at a time so I would not get them mixed up. I put the assembly back in the washer, plugged it in, pushed the power button, but nothing. Incoming voltage is good. I did notice an extra relay at the left bottom of the board that does not have a plug. The old board does not have one. What next?
1 Answer Bob, If you have power coming to the board but no display then check the wiring between the display board and the mainboard for any type of damage.If there is no damage then replace the display board. Read More...
Denise June 05, 2019 for Model Number wf350anw/xaa 01 my Samsung front load washer quit during the cycle. The front control board is still lit up but I cannot push cancel for the door to unlock. I have cleaned out the pump strainer and unplugged the machine to no avail. whats going on?
1 Answer Denise, there are a few possibilities in this situation. It is possible that a key may be stuck or that the main control is not interpreting the signals from the user control telling it to cancel. What you will want to do is unplug the unit and wait for 5 minutes, plug it back in, and the door should unlock. You will also want to check for any error codes that may appear. If the door does not unlock, there is a little tab on the bottom of the door lock that can be pulled away from the lock to disengage the lock and allow the door to be opened. You will then want to check the wiring connectors for any signs of damage or loose connections. If that checks good, then you will want to test connection CN8 pin 4 (with black probe of meter) to pin 5 for 5 VDC (red probe) and pin 6 for 15VDC (red probe). If that checks good, then you will want to check pin 1 and pin 2 with the red probe for a fluctuating voltage as this would indicate communications between the boards. If pin 2 does not have an outgoing voltage, then the main control DC92-00381A has failed. If pin 1 does not have an incoming voltage, then the user interface DC92-00383A has failed. Read More...
Terry S July 14, 2013 for Model Number wf330anw The clothes don't come out as dry as they were when I bought the washer. The spin does not seem to be as fast. The normal load usually sticks at 16 min and the quick wash usually sticks at 14 min. It takes forever for the clothes to balance in the tub. I have smelled something like a transformer or motor winding getting hot or it could be the board. Any suggestions?
1 Answer Terry, You will first want to pull the cover on the lower right corner of the front of washer and take the filter out of the pump assembly to make sure that there is not clogged or caught in the drain pump. It sounds like this may be the case because if the water has not completely drained from the unit then the unit will not spin properly. The smell could also be coming from this issue. Read More...
Mike March 27, 2013 for Model Number wf350anw/xaa Getting a 2e error (not e2). Had tech come out and tell me it is the assy pcb (front pcb). I ordered and replaced. Still getting same error. Could it be the main pcb in the rear of the machine or possibly something else?
1 Answer Mike, The 2E error code indicates a power error. You will want to check the incoming voltage to the unit. There should be between 110vac and 132vac. If there is too much or too little power then it will cause this error. If the power supply checks on then you will need to replace main PBA DC92-00381A. Read More...