Kathy August 15, 2025 for Model Number DV50F9A6EVW/A2 - 0000 Hello, I recently ordered part # DC92-01310A, the main control board for my dryer. The casing is very different than what is currently on the unit. The old board is in a low-sided casing and uses a cover on top of it, the casing on the part I was sent is very different, is this board the correct board for my dryer model? If it is correct how is it installed?
1 Answer Hello Kathy, and thank you for your question.The control DC92-01310A is correct for your model. The manufacturer has updated the mounting method, which can be confusing since no instructions are provided.The old control and its cover are no longer needed. The new control is already mounted directly into the outer cover, and the thin plate from the original control is not reused. The wiring harness feeds into the hooked opening on the new control. Once the wires are connected, mount the control onto the frame with both the control and wiring facing the panel. Read More...
1 Answer Terry H,In general check the door switch...We would need the model/serial numbers to properly research your issue and give you the correct information and part numbers for the machine you are working on. Read More...
Michele October 11, 2023 for Model Number DV50F9A6EVW/A2- 0000 The new control board part DC92-01310A doesn't look like the old board, there is not away to mount the board there are not screw holes and the housing is too big for the top of the washer. Is the part correct for the model? Are there new installation instructions to mount the main control board?
Joe June 07, 2023 for Model Number DV50F9A7EVW/A2 My dryer has very high heat, but clothes are still wet. I've cleaned filter, dryer hose & vent. Still having the same issue. Now I've noticed that none of the buttons work, cannot change temp time or any functions. Can it be the controller board?
1 Answer Yes, if you can adjust the settings there is likely an issue with the control board. Read More...
Melissa July 13, 2020 for Model Number DV50F9A6EVW/A2 S/N Y7D75AUFC00884N We are getting a HE code. Have already replaced the heatimg element and sensors, but are getting getting the HE code. What else could it be?
1 Answer Melissa,The manufacturer suggests cleaning your vent. We suggest disconnecting the vent from the rear and see if the error goes away. If it does then there is a restriction from the back of the unit to the ducting out of your house. Read More...
Tankuskc January 05, 2016 for Model Number DV50F9A6EVW/A2 Model Number: DV50F9A6EVW/A2 Brand: Samsung Age: 1-5 years All-electric Samsung dryer barely out of warranty and it stopped heating. Figured I'd try to fix it myself and save us the $150 service call. Now it's personal... I *have* to figure out what's wrong with it. Symptoms: No heat whatsoever on any setting (timed dry, sensor dry, etc.) On timed dry, any heat setting, it will run (cold) for a few minutes and then sing that little song saying it's done. Will air fluff for full time set. No error codes Here's what I've checked so far: Vents: not blocked; testing with vents off to check for warmth Lint build-up: vacuumed the interior cabinet to remove any traces of lint/dust bunnies Voltage: 240v on the outside two connections and 120v from left/right to center (checked where the plug connects to the back of the dryer) Continuity: all fuses, thermostats, heating element have continuity (including the two on the blower housing and the three on the heater duct assembly) Wiring: no scorched wires or boards, checked some for continuity, but not all Here's what I've tried replacing: DC97-14486A: Heater Duct Assembly (includes new heating element, thermostat, thermal fuse) DC47-00016A: Thermal fuse on the blower housing DC32-00007A: Thermistor on the blower housing DC92-01310A: Control Board All that I can figure is left is the timer, but it doesn't look/smell scorched or anything... Anything else it could be before I drop another $100 on a part?
1 Answer Hello TankusKC. If the wiring is good on the unit, then the other thing it may be is a bad motor. It passes power to the heating element. You can test for 120 from the motor to the heater. Just trace which wire goes from the motor to the heater. Then test it unplugged from the heater. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...