Bryan December 14, 2019 for Model Number samsung front load washer I have a Samsung front load washer that is about 5 to 7 years old. During the wash cycle the unit turns off and the door remains locked. I troubleshoot the unit and it had power through the filter down to pin 1 of cn11 to pin 4 of ry7 read 120 volts. Then I checked connector cn7 pins 4 to pin 5 should have 5 volts and it read zero volts. Then I checked to pin 5 to 6 that should have 12 volts and it was also zero volts. So, I ordered a new Samsung dc63-01573b002 Assy Pcb Main. That lasted 2 months and the washer has done the same thing. What should I look at to try and prevent this from happening again?
1 Answer Bryan, If the control board went bad that quickly then check to make sure that there are no broken or damaged wires. Also, make sure that there is no issue with power surges as this would cause an issue. Read More...
Lawrence December 26, 2018 for Model Number WF210ANW/XAA04 My front load washer only will fill in the perm press cycle i believe it to be main control board is there a good test and what is the board number
1 Answer Lawrence, With the unit only filling in the permanent press cycle this would be an issue of the main control board. You could check for 120 vac out of the board to the valves in other settings. If there is no power the board is the issue. Read More...
Bens935 May 27, 2018 for Model Number Samsung WF210ANW/XAA I have a Samsung WF210ANW/XAA. I’ve been getting the hr code. I replaced the Main PCB board with a new DC92-00301E It still comes up with same hr code. What are the odds of that one being defective too? The wires all look good, all connections are intact. Can it be the sub board DC92-00303C? I’ve had the board replaced twice prior to this. It’s now the 3rd possibly the 4th?
1 Answer Ben, This can be a short or a wire disconnected to the heater circuit. Thiscan also be problem with the tub contacting the heater or if the waterin the tub is frozen or there is no water. The error is triggered bytemperatures above 145C. If the heater has no error, this occursbecause of a PBA relay malfunction. Check the wiring harness tothe heater.An Hr error occurs if the steam heater, is faulty, replace it. Read More...
Duane December 10, 2017 for Model Number WF210ANW/XAA Good Morning, I have a Samsung wf210 front load, The problem I am having is the wash cycle is taking about 1/2hr longer then normal. everything else seems to be working like it should.What do you think the problem may be? The washer is 7 years old.
1 Answer Duane, The control board "automatically" reprograms itself to it's optimum cycle run time whenever needed. This is based on inputs from the sensors in the washer. You will want to check and make sure the washer drain hose, pump, etc. are clear/clean and not twisted or kinked. check the fill hose and fill valve screens and remove any debris or sediment from them so you have maximum water flow(you may also want to check and flush the faucets and water lines). Then make sure you're using the proper amount and type of detergent, and keep an eye out for heavy and off balanced loads. Read More...
Brian August 14, 2017 for Model Number WF210ANW/XAA I got the Hr code on my washer 6 months ago and replaced the PCB. It worked for 6 months and the Hr code came back. I replaced the PCB with a new one ( 2 new ones actually) and it goes right to the Hr code. I've unplugged and re plugged every connection and checked the continuity on the thermistor which is ok. Any idea what else I might try? Your thoughts would be greatly appreciated. Thanks, Brian
1 Answer Brian, This HR error code would mean that the heater relay on the main control board would need to be replaced which would be part number DC92-00301H. Read More...
Tony S November 03, 2015 for Model Number WF210ANW/XAA My washer looks like it lost total power I check voltage i got 120 at the plug. No display it just black like its un plugged?? Thanks for any info.
1 Answer Hello Tony. You need to test for power to the main board. If it is there, you will need to order and replace the main board DC92-00301H on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jen August 06, 2015 for Model Number wf210anw/xac01 Here is my model number for my Samsung front load washer and we need a control board.
1 Answer Hello Jen. DC92-00301H is the main control board for the model number you provided. Read More...
Jen August 04, 2015 for Model Number WF210ANW/XAA I need a new control board is this the part ap4567167. thanks.
1 Answer Hello Jen. We will need to know the version number of your washer to determine which board you need to use. Read More...
Jim July 14, 2014 for Model Number wf210anw/xaa Hi, I am working on a Samsung front loading washer. I‘ve had to replace the; what I call the spider which is part that mounts the main shaft to the inner tub. The repair went well. It came apart and went together without any problems. But when I plugged it in and turned it on to test it the code for Temperature Sensor problem appeared. I’ve checked everything I could think of. I am now wondering if it could be a poor connection at the sensor coupler?
1 Answer Hello Jim. Yes, you will need to check the connection and look for pinched, bad, or broken wires on the unit. Read More...