Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Ball, Check by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18043290
Manufacturer Part Number: WP99002281

Questions & Answers

For Whirlpool Ball, Check (Part Number: OEM18043290)

William for Model Number MDB9150AWW

My question is about the check ball. On dissasembly, I found no check ball in place. On your video, I see there IS a white checkball--about 3/8 in dia. That makes sense, since there is a 'receiving' area on the underside of the gray plastic drain cover--I can see how a 3/8 (approx) ball would be meant to get sucked up and into place into the underside of the drain cover, blocking the flow of water in one direction. BUT your replacement part is a tiny blue ball. If I place that there, it will get sucked up and away into the system--the receiving place in the drain cover being too large. SO, MY QUESTION: Are there two different styles of drain cover that accept two different sizes of ball? And, if there are, can you please confirm my suspicion that i should not get the small blue check-ball since that will not work with a drain cover that needs a larger ball. Thank you!

1 Answer

William, There is only one check ball that should be in this unit and it would be located under the drain cover. It is possible for the check ball to get smaller so you will want to replace the check ball. Also check the discharge housing to make sure that the bottom plate has not separated from the top.

Read More...
Harry for Model Number MDB7100AWW

I have taken my dishwasher apart to find out why it wasn't washing. Found out it was all calcified up. However... I found a checkball in part number PS2099287, called a filter support. It was a small blue checkball. There is no checkball under the drain cover. The blue checkball is way too small to go under the drain cover. The one I found goes between the suction base and the filter support, at about the 3 oclock position in the second picture of the filter support. Your diagram doesn't show one there at all. My serial number is 27692379ZQ

1 Answer

Harry,

There is only one check ball that should be in this unit and it would be located under the drain cover. It is possible for the check ball to get smaller so you will want to replace the check ball. Also check the discharge housing to make sure that the bottom plate has not separated from the top. You will also want to check how much detergent is being used and maybe use less. Also if you are prerinsing the dishes this can also cause the ball to get smaller.

Read More...

1 Answer

Budweiser, Part #39 is the check ball, there are two different sizes 99001798 and WP99002281, depending on series/serial number. Once you have the drain cover 99001795 removed, You should see the indentation for the check ball molded into the outer pump housing. You'll need to install everything below the drain cover first. then is you use some water soluable grease, and put a dab in the indentation, set the check ball in the grease, and then install the drain cover, you may find that a bit easier to work. Once everything is installed, when you test the dishwasher, the water will remove the grease, and everything will be fine from there.

Read More...
Bill for Model Number MDC5100AWW

Hi. I just bought a check ball from you. It was part AP4113233 according to your website or part #99002281 that was on the package the ball came in. It was blue in color. The problem is the ball seems exceedingly too small. I have a venier caliper and the ball measures 1.565 while the hole in the drain cover measures 3.750. If I put the ball in the sump beneath the drain cover, it will come up the top and into the plate filter. I can't seem to find any other size ball check. Can you offer some assistance? Thanks, Bill

1 Answer

Hi Bill. There is a gray top cover internally part # 99001795 that the ball is directly placed under. It has 2- long parallel passageways. On the lt. end there is a opposite indention where the ball area is placed. It is there to have the ball the area to lift and stay above the water flow. Then as the water is not flowing in this direction, it is held in place and acts as a check valve (check ball). This place is at the outer edge of the sump area and not the middle. Thank You.

Read More...
Glenn for Model Number MDB7100AWB, ser # 15869753YU

I have disassembled the machine as I am replacing a broken wash impeller and discharge housing. I have discovered that my machine does not have a check ball (part#39) installed under the drain housing(part#20). It appears that there has never been a ball there - I purchased this machine new. My machine is installed with an anti-siphon airgap. Is there a reason to install a check ball? Has the ball deliberately been omitted from the machine to avoid a potential blockage problem?

1 Answer

Hi Glen. We have researched the tech. bulletins for your model. All breakdowns do allow for the check ball. It may have been missing from the initial assy. time frame. This ball permits the proper wash and rinse sequence to happen w/ out any back draining into the pump assy. That part # is WP99002281. Thank You.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google