Joe March 06, 2013 for Model Number MER6770AAC Maytag Gemini Dual Oven. I replaced the sensor probe in the upper oven after getting F-1 Error messages. Now neither upper nor lower oven will come up to the temperature set on the keypad. Or if they do come up to temperature set, they don't hold that temp and will not go to a higher temp. Do I need to replace the entire keypad assembly, or is there something else to look at? Thank you.
1 Answer Joe, Based on the information this issue will be caused by a faulty clock assembly 12001661 and will need to be replaced. Read More...
Greg E February 27, 2013 for Model Number MER6770AAB Just bought this stove and worked fine, but now it sets off code F1-8. What do I do?
1 Answer Greg, The F1-8 error code means a shorted keypad and you will have to replace the control 12001661. Read More...
Teresa February 01, 2013 for Model Number MER6770 AAB Just replaced part number 12001661-and now getting F3-2 and now both ovens are heating up without being turned on. Now what?
1 Answer Hello Teresa. F3: Open or shorted sensor. The cancel keyresets the control and stops the alarm. Iffault is still present it will reactivate thealarm when a cook mode is chosen.Correction: Check sensor and wiring forshorted or open circuit. Read More...
C. Cleary December 28, 2012 for Model Number MER6871AAB My oven over heated and I get a F1-7 on the control panel. I have a Maytag Gemini double oven.
1 Answer Hello C. Cleary. Keypad Disconnected. Replace Control WP5701M406-60 on the unit. Read More...
Todd September 05, 2012 for Model Number MER677OAAB My top oven keeps getting hotter and hotter and hotter. We disconnected it so as not to burn house down. The light in oven will blink on randomly now as well and sometimes one of the top burners when on will get hotter and hotter and hotter as well. Is this a computer main board issue? And if so what part do I need to fix. Stove is less than 3 years old.
1 Answer Hello Todd. Based on the information you provided, it sounds like the clock assembly 12001661 is bad and will need to be replaced in the unit. Read More...
James G. July 12, 2012 for Model Number MER6770AAW Problem with double free standing oven: (Maytag Gemini oven). When using upper oven get this error message: F1-2 for suspect failure area "Runaway Cook Lower Oven" When using lower oven do not get any error message. Correction for this message is "Check temperature sensor which should read 1050 - 1100 ohms." Replaced sensor but still get same error message when using upper oven and no message when using lower oven. I suspect the oven control but with this question; why get this error message for the lower oven when using the upper oven and no messsage when using the lower (suspect) oven. This same message appears on the control message assembly from 30 to 60 minutes after being cancelled. This clock/control assembly is about the most expensive of all control assemblies used in these electric ovens. I would like to be absolutely sure that this assembly "AP4009010" is the the defective part in need of replacement. Furthermore, both ovens appear to be working properly; i.e reaching and holding the desired temperature. Conclusion: there is no "runaway cook lower oven" problem; since both ovens work proerly in use (i.e. attaining preset temperature and maintaing that temperature). The error message appears to be false and the real problem is "What is causing the error message?" What do you advise and WHY?
1 Answer Hello James. Based on all the information you provided, it sounds like the clock assembly 12001661 is bad and will need to be replaced. Here is the reason. We know the sensor is good because it is new. All the sensor does is send an ohms reading to the clock and then the clock determines if the temperature is correct. Two parts are controlling this code, sensor, which is new, and clock, which is bad and causing the code. You will need to replace the clock on the unit. Read More...
1 Answer Hello. Based on the information you provided, it sounds like the clock assembly 12001661 is bad and needs to be replaced. Hope this helps. Read More...
Donna February 10, 2012 for Model Number MER6770AAC In conversations above about part # AP4009010, the responder referred to the part as a control assembly and on another occasion, clock assembly. What is the part?
1 Answer Hello Donna, part number 12001661 is considered a control board or a clock assembly. Depends on the manufacturer what they name it. The control panel is the part this clock/board will mount to. Thanks! Read More...
Nel October 27, 2011 for Model Number mer 67700 aaw My top oven would not get up to temp replaced the bake element but had no luck. Top bake element will not get hot.Could it be the Clock Assembly? I replaced this same part about 16 months ago. Any help?
1 Answer Hello Nel. Test and see if there is power going to the bake element in bake mode. If not, and the wires are good, you will need to replace the clock assembly 12001661. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Chris C. June 29, 2011 for Model Number MER6770aaw Bought a replacement oven control unit. Took out the old one and started to reconnect the new one and have a few plugs that I can't remember where they go. Is there a diagram that indicates what goes where? I don't want to screw this up.
1 Answer Hello Chris! Please use the following links to view the wiring diagram listed for your model MER6770AAW. This will help determine the location of the wires. Thanks!http://www.appliancepartspros.com/partsearch/model.aspx?model_id=46855&diagram_id=28479158#d28479158http://www.appliancepartspros.com/partsearch/model.aspx?model_id=46855&diagram_id=28479159#d28479159 Read More...