Susan Howe December 30, 2017 for Model Number WP74007217 We have a broken Jen Air Clock with Harness getting F 1-8 error code. They no longer make the replacement clock. Any ideas on how to fix it or which replacement parts could be used. Any help is greatly appreciated.
1 Answer Susan, The manufacturer no longer sells the part. We can no longer get it from any of our suppliers and there is no substitute for the part available to us. We don't know of any other source for the part. You may want to try contacting local parts dealers, one of them might still have it in stock. Enter your part number in a search engine, a smaller company might have it. Try eBay, Amazon or similar sites. Search by using the manufacturer's part number [74006387] You can also try a used appliance store, sometimes they have the same model or usable part for your machine. Contact refurbishing companies, especially for circuit boards:•www.circuitboardmedics.com •www.corecentricsolutions.com www.generaltimerepairs.com . They may be able to repair or refurbish the clock/control you have. Read More...
Connie March 16, 2017 for Model Number Jenn-Air Gas (dual-fuel) Slide-In Range Model #JGS8850ADS The LED readout is F1-8. We can sometimes use the oven and other times we cannot use control panel to turn oven on. Beeps every now and then, sometimes more constant. Control board was replaced 2 years ago. Oven igniter also replaced 2 years. Burners also malfunctioning. Try to light one and it just clicks and sparks, no flame right away. Sometimes flame is immediate, but another burner will click and spark for several minutes while cooking on first burner. These problems affect all 4 burners at different times. What are the problems. Can they be fixed. Is it worth it? Stove was purchased in 2002.
1 Answer Connie, For the F1-8 error code this would be a faulty keypad which you would need to get the control panel WP74005739. For the issue with the top burner, make sure that all the burners are clean and if they are then there would likely be an issue with the spark module or ignition switches on the top valves. Read More...
Barry December 08, 2016 for Model Number JGS8850ADW When I try to use the oven, it seems to be working, as it preheats and gets close or up to temp, but then it starts beeping and the code I get is F1-7. What do i need to do to fix this?
1 Answer Barry, The F1-7 is a membrane disconnected error. You will want to check the ribbon harness connected to the control board to ensure it is securely connected, make sure that there is no corrosion, shorts or breaks in the ribbon harness. If this checks ok then replace the control board. Read More...
Ken October 19, 2014 for Model Number JGS8850ADS If I press the 9 or 0 while setting the temperature it cancels everything. I assume I need to change the control panel.
1 Answer Ken, Correct you'll need to replace the control panel assembly WP74005739. The keypad circuits have started to degrade and are causing the ERC/Clock to shutdown, due to misinformation in the inputs. Read More...
Oliver January 14, 2014 for Model Number JGS8850ADW Is the part needing replacement on a error code F1-9? Thank you.
1 Answer Hello Oliver. Yes, F1-9 Internal control communication errors. Replace control. Read More...
Carl January 28, 2012 for Model Number JGS8850ADW What does it means when you get an error code F-1 and F-3. I replaced the oven sensor and thought that will solve the problem but it didn't. The oven shuts down with error F-1 and sometimes error F-3.
1 Answer Hello Carl! An F3 error indicates a shorted or open sensor. Check the wiring between the clock and the sensor to make sure it is ok. The F1 indicates a defective or shorted touch pad or clock. The clock is part number WP74007217 and the touch pad is part number 74005740. You will need to run the following test (below) to see which part to replace. Hope this helps, thanks!This simple test will help determine whether the ERC (Electronic Range Control or Clock) or the touch pad is defective when F1 error code is present.Note: Some models incorporate the touch pad in to the ERC as a single assembly, in which case this test is not necessary. Simply replace the ERC (Clock).Warning: If you feel in any way uncomfortable performing this test or making this repair, please contact a qualified appliance repair technician.1. Disconnect power to the range (unplug the range power cord or turn the power off to the range at the circuit breaker). It is very important that the power to the range has been disconnected, so please double check before continuing.2. Gain access inside the control panel.3. Disconnect the touch pad (also called keypad or membrane switch) ribbon from the ERC.4. Make sure there are no lose wires, or anything else that may cause a short when power is turned back on. Assemble the control panel back the way it was.5. Turn the power back on.6. Wait for at least one hour to see if the F1 code comes back (usually accompanied by a beeping sound).7. If F1 comes back, replace the ERC. If it does not, replace the touch pad. Read More...