Greg December 19, 2021 for Model Number KSRP25FNSS00 Condenser Fan runs consistently. The unit runs cold and the temperature setting has no effect. is this the board or something else? Just replaced the fan, it was noisy, but it was running cold before but did shut off. There was water in the defrost pan.
1 Answer Greg, if the thermistors WP2188819 tested good, the failure would be in the main control 8201673. Read More...
Xuan August 31, 2021 for Model Number Kitchen Aid KSRP25FNSS00 Hello, The LED bar indicator at refrigeration temperature setting on controller panel (at top inside my refrigerator) does not lite. Indicator "Freezer" lite on OK and works fine. The fridge side is running warmer than usual at ~40 degree F. Should we change the controller board WP 8201673?
1 Answer Xuan, the LED bar not illuminating would certainly be a failure in the control board 8201673 which could also be the cause of the refrigerator being warmer. Read More...
Jeff March 14, 2021 for Model Number KSRP25FNSS00 Have to defrost manually every 2-3 weeks. Thermistors check ok. Ran self diagnostics test to check for power at defrost heater. Getting 110 volts. Plugged heater back in and checked ok. Defrost t-stat checks ok.
1 Answer Jeff, If the heater is getting power and coming on and the thermostat and thermistor test ok then this will be a faulty control board that is not sending the unit into the defrost cycle. Read More...
Aggie April 01, 2019 for Model Number KSRL25FRST04 My Kitchenaid started making an 'alarm' sound this weekend. I was able to diagnose that the sound was coming from this board (part # AP3713826). I took the cover off, confirmed this was the source, and when I put the cover back on the alarm sound stopped. Before I buy a part to replace, can you give me an idea what might have caused the alarm sound? I have a feeling it is a symptom and I would like to get a feel for the actual problem before I starting replacing parts.
1 Answer Aggie, there may have been a loose connection at the control board that when re-installed may have been corrected. Usually this board will start creating an alarm sound when there is a temperature issue within the appliance. The thermistors could be tested to ensure that they are operating properly, and if they are, then that will indicate that there may have been either a loose connection (it would be best to look for loose connections when testing), or that the control had an intermittent failure. Read More...
Ryan March 30, 2018 for Model Number KSRP25FNSS00 After installation does it have to be programmed? Mine seems to be defrosting too often. Every 6hrs?
1 Answer Hello Ryan, This board does not require programming. It will defrost as often as it senses that defrosting is needed. Read More...
Mike July 31, 2017 for Model Number KSLR25FRST04 Frige will run for days,shut off for 14 hours,then start and run perfectly. I cleaned the condenser,fan runs,evap fan OK also.
1 Answer Hello Mike. Based on the information you provided, it sounds like the electronic board 8201673 is bad and will need to be replaced on the unit. Read More...
Jeff May 04, 2017 for Model Number KSRL25FRST04 The refrigerator and freezer stopped working after 10 yrs. The fan in the freezer on the back wall does run when the appliance is plugged in. The coils underneath are as clean as I can get them as they are difficult to get to. I tested the compressor with a multi-meter and it seems to be ok. I get resistance readings on each pair of terminals. There is no clicking noise when the appliance is plugged in and the condenser fan is not running, however it is not stuck either...can turn freely by hand. I did shake the relay and there is a slight rattle. When I check the voltage at the condenser fan it registers 0.1. There is power to the control board and the lights for the freezer and refrigerator temperature settings are lit. The power button does turn the fan in the freezer on and off. The lights for the ice/water dispenser are lit. Is this a control board issue or something else? I just want to make sure before I purchase the board.
1 Answer Jeff, Based on your post information, you will need the main control board 8201673 / 8201673 ELECTRONIC CONTROL BOARD. First check to make sure you have 120 VAC across the the black and white wires on the P1 connector wire harness to the board. If you have the voltage replace the board, The part is in stock and available at this time. Thanks, Read More...
Merel October 09, 2015 for Model Number KSRL25FRSS00 The freezer is OK but food in the refrigerator is freezing, especially on the top shelf rear. The defuser is open all the time. I replaced it with a new one that was closed when I installed it but the new one opened and has not closed. I checked the thermistor for resistance and it changes when placed in ice water so I assume it works also. What next? Maybe the control panel? If so, you list two for my model and I would like the part number to order.
1 Answer Hello Merel. It sounds like the thermistor is not reading properly and will need to be replaced on the unit. Read More...
Jt December 16, 2013 for Model Number KSRP25FSSS00 Any idea when part number 8201673 (refrigerator electronic control) will be available? I have been trying to get this part for over one year with no luck!!!!!!!! JT
1 Answer Hello JT. Sorry, 8201673 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Shawn July 26, 2013 for Model Number Ksrl25frst04 The defrost is not working I checked the element and the thermostat that controls it all was good. I defrosted the coil my self and all is back to normal. Is my control board bad??
1 Answer Hello Shawn. If the defrost thermostat and heater is good, you will need to replace the board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...