Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Water Valve Tubing Coupler by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18064530
Manufacturer Part Number: WPW10445062

The Water Valve Tubing Coupler is an OEM part for Whirlpool dishwashers. It connects the water valve to the tubing, ensuring a secure and leak-free water supply to the appliance. Note: The compression connection is for the 1/4" water supply line. The "Quick-Connect" outlet of the fitting is 5/16" in diameter.

Replace this water valve tubing coupler if it becomes worn out or damaged. Over time, the coupler can degrade due to constant exposure to water pressure, mineral buildup, or accidental mishandling. A faulty coupler can result in water leaks or insufficient water supply to the dishwasher.

Symptoms of a bad Water Valve Tubing Coupler include:

  • Water leaks around the coupler area
  • Reduced water flow to the dishwasher
  • Dishwasher not filling properly
  • Visible cracks or damage to the coupler

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

More
$71.95

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Water Valve Tubing Coupler (Part Number: OEM18064530)

1 Answer

Len,

If you put a jumper between T and H, this will cycle the icemaker. Check to see if there is power when it gets to about the 11 o'clock position, there should be power from V to N and if there is not then the icemaker will need to be replaced and if there is then the valve will need to be replaced.

Read More...

1 Answer

Tony, Yes, you will want/need to use the WPW10445062 Connector it serves several purposes, besides a way to attach the water supply line from the plumbing to the refrigerator water system. It also reduces the possibility of a major water leak at the dispenser or ice maker. It's not a difficult repair to make, disconnect the water, remove the connector valve from the fill valve bracket and reverse the procedure to mount the bracket and valve(s) and flush and attach the water supply line.

Read More...

1 Answer

Jim,

The connector is for the purpose of connecting the supply line. You can eliminate the connector but will have to install new tubing to the water valve inlet. This tubing will have the connector to attach to the water supply and is part number 8201597.

Read More...

1 Answer

Ken,
Use a jumper wire and jump the terminals on the face of the ice maker under the white cover labeled T and H. If voltage is present the ice maker will start a harvest cycle. At this time you will want to check for 120 Vac at the water valve solenoid for the ice maker. If you're not sure just follow the water line from the ice maker.If the unit will not cycle then probably have an issue with the optics of the ice bucket. Note; when you jump the ice maker and the dial starts to turn you will need to remove the jumper after it cycles about a quarter turn. You will need a multimeter to test for voltage. Also, don't forget to check the fill tube for blockage. This would be a water valve issue.

Read More...

1 Answer

Allan, the water flow should go to the filter, from the filter to the inlet valve which has the solenoid for the ice maker and water dispenser. You may want to check the water pressure, as well as ensuring that all of the air has been removed from the filter and water lines. More than likely the valve may be getting stuck which can be caused by wear and tear or by water pressure. The water valve can vary based on model and there are several models that contain KSRA25C. You will want to verify the correct part by the full model number that can be found in the top right hand of the refrigerator.

Read More...

1 Answer

Tony,

On this unit there would not be a prefilter and you would only have one filter and the filter housing. If there is no water flowing through the unit and it has a good filter then the housing would be the most likely issue.

Read More...

1 Answer

Hello Chairman 101. Sorry we do not have a video at this time. We are working daily at adding new videos to our site. Thank you.

Read More...

1 Answer

Hello Ken,
The only thing that can cause hollow cubes is an insufficient water fill. You will need to verify the fill at the end of a cycle. An insufficient water fill can be caused by the filter head or a stopped up filter on some designs and there could be a partially frozen fill tube or crimped water line. For a more specific diagnosis, please provide the model number from the units' I.D. tag.

Read More...

1 Answer

Michael,

The tubing that goes to part number WP2304697 which should be 5/16" but may be 1/4". This part will be the correct part.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google