Craig August 19, 2019 for Model Number 106.52552100 Hi, Attempting to clean rust stains inside my Ice Bucket Assembly, I disassembled the metal auger components. Problem is, I can't recall the order of re-assembly. Do you have a schematic showing where/how all the nylon washers and metal auger components go back together? The Ice Bucket Assembly # is: WP 2315404
1 Answer Craig, the lower bin WP2212372 will have a diagram for this located just under and to the left of the main image. This diagram can be used to assist with re-installing the bin components. Read More...
James June 18, 2016 for Model Number 51269102 I have a Kenmore refrigerator purchased 2001 from Sears. We lost power for two days. Once i removed my icemaker bin that holds all the ice. It will not sit propertly in the holding position. It wiggle out when i try to get ice out. If i remove all the ice and hold the ice bin down, it will turn but still try to pop up when the drive shaft connect with the upper end to turn to ice out. Is the connecting end that hold it in place worn. Please help.
1 Answer James, You will want to check to make sure that the locking mechanism on the bottom of the bin. If this checks ok then you will want to check the coupler on the door to make sure that it is not frozen to the shaft and causing it to pop up. Also check to make sure that the auger is rotating and not stuck. Read More...
Connie April 05, 2016 for Model Number 10650582001 I am trying to replace the ice bucket assembly unit. My unit got rusty at the bottom where the crusher mechanism is located. What part number would fit? I had been given 2315404, but it is awful pricey
1 Answer Hello Connie, I'm sorry but WP2315404 is the only ice bin assembly listed by the manufacturer to fit the model provided. Read More...
Stacy November 05, 2014 for Model Number 10652552100 The release lever/button broke when I was removing the ice bin. Can you replace just the lever/button instead of buying the whole bin?
1 Answer Hello Stacy, The individual parts on this bin are available separately. You will either need the button WP2315403 or the latch 2256015. Read More...
Paul August 11, 2014 for Model Number 10653632300 The ice going in crushed ice bin ok. The auger turns ok but more and more times it seems ice is getting stuck and frozen and in little pieces at the bottom of the bin that connects top of chute that ice drops from. Then it seems like the ice melts enough there to quit dropping with the auger still turning.
1 Answer Hello Paul, You will need to clean the ice bin out often enough to prevent the smaller shards of ice from freezing together and clogging the crusher bin. You also need to wipe out the ice chute with a hot rag since smaller chips of ice tend to stay behind and since dry ice sticks to dry ice, will cause an "ice cube traffic jam". You should also remove the crusher bin and shine a bright flashlight into the dispense area while looking down into the ice chute. If you can see light, the ice door WP2180353 is not seating properly and will have to be replaced. Read More...
Kathy July 12, 2014 for Model Number 106.56662500 Will not dispense the ice thru the door. Making ice fine and dispensing water. Is the problem in the door or could it be the storage bin?
1 Answer Hello Kathy. You need to check for power to the auger motor in the unit. If there is power to the motor, and the motor does not run, you will need to replace the motor. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Lea December 30, 2013 for Model Number 10656544400 Placed a cup under the ice dispensing bin depressed the button and the arm did not turn to dispense the ice. I removed the bin checked for ice blocking the arm....nothing there, took it out and let it dry out replaced it and nothing...I need to know if I need a new bin or if it could possibly be something else. The water still dispenses with not problem and the ice maker is working properly as well. Thank you for your help!
1 Answer Lea, We attempted to send you the information and checks you would need to make at the dispenser switches and motor. Our e mail was returned " Delivery to the following recipient failed permanently:Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the server for the recipient domain .The error that the other server returned was:Recipient address rejected aol.com. If you still need our assistance please repost your question. Read More...
John April 18, 2013 for Model Number idk; part #1175525 remove ice bucket assembly because it was frozen; tried to replace after thawing; shaft on bottom seems to have rised up and bucket will not fit flat into freezer
1 Answer John, You will want to remove the cover over the shaft and there is a white plastic shroud on it that will have to be slid higher on the shaft. Once it is in proper position the ice bucket will sit properly. Read More...