Anthony October 07, 2019 for Model Number WP25DQXDB02 Ice Maker dispensing door not closing completely. Could it be the dispenser motor WP1120581 ? or something else?
1 Answer Anthony, The delay mechanism could be causing the door to not close completely and would part number WP1120581. Also check the ice door to make sure that it is not damaged in any way. Read More...
Greg September 02, 2015 for Model Number ED22GWXWW10 How do I remove the Ice/water dispenser faceplate without damage? Are there stubborn clips or hidden screws? The plate is not available and I dont want to break it. I am trying to get to the noisy Icemaker Delay motor. Thanks
1 Answer Hello Greg. There is no screws. You will use a flat blade putty knife and unsnap the cover from the door on the unit. Be careful as the part is discontinued and is no longer available. Read More...
Welton D August 15, 2015 for Model Number KSRS27QAAL05 My icemaker died, found a bad water valve and replaced it. Still no ice, checked voltage on the module had 119v Line to nutral and on the heater to neutral. REF MOD#KSRS27QAAL05
1 Answer Welton, You will want to jump out the T to H on the icemaker to make the icemaker go through a cycle. Once you do this you will want to test for 120 vac getting to the water valve. If there is power to the water valve then the icemaker module would be the issue. If there is 120 vac to it then make sure that the fill tube is not frozen. Read More...
Chris G October 27, 2013 for Model Number Kitchen Aid built in refrigerator-freezer #KSSS36DWX00 The door on the ice dispenser is making noise when it closes.Like a loud almost whining noise.what could that be?
1 Answer Chris, The icemaker delay WP1120581 on the dispenser would most likely be the cause of the door making a whining noise when closing. The other part that would possibly make this noise would be the mechanism 482722 that holds the door. Read More...
Rosie October 23, 2013 for Model Number ED22PWXDW00 My ice dispenser motor/auger was taking longer and longer to stop and now it won't stop at all when the dispenser door closes. Had to unplug the fridge. Can't figure out which part controls the motor. Can someone please help?
1 Answer Hello Rosie. WP2162361 is the part you need to check. It is the micro-switch in the dispenser assembly. If it is stuck closed, you will need to replace the micr-switch on the unit. Read More...
Joe August 12, 2013 for Model Number Thermador tss48qbb I need to replace the Delay Mechanism (Part #00416002) and I can't find the part. Someone suggested the Whirlpool Part 1120581 is compatible. Any chance that this is true?
1 Answer Hello Joe! The delay mechanism 00416002 has been discontinued with no further replacements or cross references available and our company is unaware of any other available sources. Sorry about that! Read More...
Doug June 16, 2012 for Model Number ED20TWXDN00 Ice maker makes cubes, but the dispenser does not dispense. The auger does not rotate. Actuating the ice lever causes the flap to open and it makes some electrical/vacuum (?) sounds.
1 Answer Doug, First thing to check is the dispenser wiring harness, it's located at the freezer door hinge bottom, make sure there are no loose connections or damaged wires, Then remove the dispenser facade " NOTE: Flush Look (Built-In) Models - Remove the two trim-panel channels at the top and bottom of the front cover before attempting to remove the dispenser assembly. 1. Remove the switch cap and unsnap the two (2) tabs at the bottom of the front cover from the housing first. Pull the bottom out and lift and the front cover from the housing. Remove the two (2) hex-head screws securing the metal control panel cover to the dispenser housing. This will also free the control bracket from the housing although it will remain tethered to the freezer door by the wiring harness. Disconnect the wiring harness connectors from the terminals on the switches and light fixture in the control bracket." You should now have access to the dispenser paddle, actuator switches and wiring, and pivots, so you can determine the issue. Thanks Read More...
John April 16, 2012 for Model Number ed25dqxbn00 How to remove the plastic frame to replace the delay on ice flap on ice despencer? Should I also replace the flap door to make sure of good seal.
1 Answer John, Here are the basics " Servicing the Dispenser Assembly NOTE: Flush Look (Built-In) Models - Remove the two trim-panel channels at the top and bottom of the front cover before attempting to remove the dispenser assembly. 1. Remove the switch cap and unsnap the two (2) tabs at the bottom of the front cover from the housing first. Pull the bottom out and lift and the front cover from the housing. 2. Remove the two (2) hex-head screws securing the metal control panel cover to the dispenser. 3. Disconnect the wiring harness connectors from the terminals on the switches and light fixture in the control bracket. If you need to, Removing the dispenser assembly 1. Do the previous three procedures. 2. Remove the eight (8) hex-head screws securing the dispenser housing to the freezer door. 3. Carefully pull the housing from the door. 4. Pull the water supply tube from the top of the dispenser housing. 5. Pull the wiring harness leads from the dispenser housing. 6. Disconnect the wiring harness connectors to the electric foil heater. housing. This will also free the control bracket from the housing although it will remain tethered to the freezer door by the wiring harness." Yes, you ought to have the ice chute door assembly WP2147167 as well. Good Luck and Thanks Read More...
Frank D. August 15, 2011 for Model Number ED22DQXEN The ice dispenser flap/door is not closing all the way and is allowing the icemaker to freeze up. It seems that the AP2978182 delay I/M is not closing. I have removed the part. I can move it counter clockwise but it will not return. Is this part bad? Thanks, Frank D.
1 Answer Hello Frank. Based on the information you provided, it sounds like the delay WP1120581 is bad and will need to be replaced. If it does not close the flapper back, the new delay should repair your problem. Hope this helps. Read More...