Sam J November 21, 2013 I just installed the new designed soap dispenser into my kitchaid dishwasher Part # W10616003...the 2 additional wires that are for the rinse aid sensor I was told to just wrap them with electrical tape as they aren't needed. Also I'm not sure of where and how to add the rinse aid. There seems to be a dial inside one of the sides but hard to add the rinse aid there. Am I doing something wrong?
1 Answer Hello Sam. You remove the cap and pour onto the top of that dial to add the rinse aid. Read More...
Chris October 30, 2012 for Model Number KUDC25CHBL1 I recently bought a new soap dispenser (Order 2901018) and need instructions on how to access the inside of the door to remove old and install new. Thanks.
1 Answer Hello Chris! You will need to open the dishwasher door, remove the inner door panel screws, and remove the inner panel. Once the inner door panel is removed you will have access to the dispenser assembly WPW10616003. Remove the wiring and screws to the dispenser assembly and install the new dispenser in reverse order. Thanks. Read More...
Astreit October 03, 2012 for Model Number KUDS24SEWH2 I am trying to replace the dispenser unit (part no. 8193920) and I'm having a problem simply removing the inner panel to get at the dispenser unit. I removed all 10 screws and the front panel came off but the inner panel is still stuck in place. What am I doing wrong? I could use step-by-step instructions. The power to the dishwasher was turned off at the circuit breaker.
Jeff May 17, 2012 for Model Number KUDS25SHBLO Thanks for the installation help; Also, before I begin the repair, I want to make sure I have the proper tools. Please advise what tools will be required. Thanks again
1 Answer Hello Jeff. You will need a number 20 torx bit and nut driver to remove the screws. You may need some needle nose pliers as well. Read More...
Jeff May 15, 2012 for Model Number Kitchenaid KUDS25SHBLO I need to replace the soap dispenser unit and I have identified the part as #3591506. I have two questions: what tool is needed to remove the screws that hold the inner door assembly? Second, is there a step by step installation instruction sheet available? Thanks!
1 Answer hELLO jEFF. 1. Disconnect electrical power from dishwasher.2. With dishwasher door closed, loosen the two (2) toe panelscrews, but do not remove them.3. Remove two (2) screws from top of access panel. Pull top ofaccess panel away from door, lift up and remove. See Figure 4.4. Remove two (2) screws from bottom of outer door panel.5. Refer to detail inset in Figure 4. Slide outer door paneldownward until slots in door panel align with slots indoor frame, then pull door panel straight off.6. Disconnect electrical connectors from terminals ofdispenser solenoid.7. Referring to Figure 5, remove the two (2) metal dispenserretainers: First remove the two (2) outer edge screws fromthe control mounting bracket and detergent dispenser shield.Next remove the three (3) screws from the bottom retainer,releasing it. Reach under the detergent dispenser shield toremove the remaining screw from the center hole of theupper retainer. Set the retainers aside for later reinstallation. 8. With dishwasher door open, reach under and pressthe tabs at each end of dispenser to release it. Liftdispenser WPW10616003 up from inner door panel to remove it.9. Remove blue rinse aid cap to take note ofrinse aid dial setting, then replace cap. Read More...
Mark December 29, 2011 for Model Number Kemore Elite model # 66515972992 The original dispenser have and additional 2 wires from the one I received. What are the two additional wires for and do I need to send back the part I ordered? The part I received was part # ap3591506
1 Answer Hello Mark. The two wires goes to the dispenser solenoid WPW10616003 on the back of the dispenser. Based on your model number, this is the correct dispenser. Hope this helps. Read More...
Mark December 29, 2011 for Model Number ap3591506 The original dispenser have and additional 2 wires from the one I received. What are the two additional wires for and do I need to send back the part I ordered?
1 Answer Hello Mark. We will need your model number to help you with this. Thanks. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Gary August 19, 2011 for Model Number kitchenaid dishwasher actuator for dispenser AP3591506 My unit is missing the actuator that opens the soap dispenser. Can this part be purchased to fix my dispenser assembly?
1 Answer Hello Gary. No, they do not offer just the actuator, you will need to order the dispenser assembly WPW10616003. Hope this helps. Read More...
James B. July 10, 2011 for Model Number kuds24sebl1 I have a kitchen aid whisper quiet ultima superba: kuds24sebl1. All my searches keep pointing me to this part but it looks very different to the one that is installed. Any idea if it will fit? Thanks, James.
1 Answer Hello James! Yes, the dispenser assembly WPW10616003 is the correct part used on your Kitchenaid Dishwasher model KUDS24SEBL1. The part has been redesigned so it may look different, however, it will work and fit on your unit. Thanks! Read More...
John S. June 30, 2011 for Model Number KUDI24SEAL1 Does the rinse aid dispenser cap come with this unit (Part Number: AP3591506)?
1 Answer Hello John! Yes, the dispenser assembly WPW10616003 includes the dispenser cap WP9743399. Thanks! Read More...