Todd November 15, 2015 for Model Number JGR8855BDS I am receiving the F9 error code. I believe it is the lock latch as I have gotten it to clear by manually moving the latch and leaving it in a place until the F9 code clears. It appears as it the gears are sticking and not allowing the latch to return to the normal position. What is the best way to expose this latch mechanism? The manual indicates the top in non-removable and I can somewhat confirm this by the rigid gas lines. Thanks
1 Answer Hello Todd, You will need to rotate the burner assemblies about 1/4 turn counterclockwise to remove them. You can then release the spring clips at the front corners so the main top can be raised. Once raised, you should have easy access to the door lock assembly. Read More...
Miriam October 18, 2014 for Model Number JGW8130adb Door latch keeps moving to open and lock code F9. It won't stay locked. It will open and lock again.
1 Answer Hello Miriam, This will either be a bad control WP5701M534-60 or a bad door lock assembly WP74005575. Read More...
Justin December 05, 2012 for Model Number JGW8130ADW/ SERIAL #1085735WM After going throught the cleaning cycle on our oven the F9 fault code appears on the display.The door stays locked. Ii have unplugged the unit as well as reset the breaker with no success. I would love to fix this oven as it is extremely hard to find 30" wall mount gas ovens. What parts or part do I need to get to fix this problem?
1 Answer Hello Justin, Either the motor or one of the switches has failed on the latch assembly. You would need to replace latch assembly 74003559. Read More...
Steve November 26, 2012 for Model Number MGR 5880 BDW The oven was on for 45 min at 350, when it started to be beep and display the F9 code. I unplugged it and let it sit for a couple hours. When I plugged it in, it did the same thing. How can I confirm that the door latch assembly needs to be replaced? Or is it something else?
1 Answer Hello Steve, You would want to check the wiring to the door latch and check the door latch itself. If the latch and wiring look good then you would need to replace the control 5701M518-60. On the latch unlock switch should have continuity through it if it is closed. If there is not continuity and the door latch is unlocked then you will need to replace latch assembly WP74005575. This will be the switch with black and tan wires. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jackie January 05, 2012 for Model Number MGR5750ADW tHE LOCK ON MY OVEN DOOR WAS STUCK. I RESOLVED THAT PROBLEM BUT NOE THE LATCH WILL NOT RETRACT AND I CANNOT CLOSE THER OVEN DOOR.i HAVE UNPLUGGES IT AND THAT DID NOT RESET IT
1 Answer Jackie, You will need to do one of two things, a) program the clean cycle waiit a couple of minutes, then cancel the cycle, hopefully the motor will retract back to it's unlocked position. Otherwise, you will need to raise the cooktop and access the latch assembly and uninstall it, until you can test the switch circuits and motor, or replace it. Thanks and Good Luck Read More...
Scott H. April 15, 2011 for Model Number MGR5770ADW The door lock latch stays in the lock position and is not letting the oven door to close. I disconnected the power source after a few minutes and reconnected and tried the control lock to no avail. What can I do to get the latch to work again. If you have an answer it would be greatly appreciated. Thank You, Scott H.
1 Answer Hi Scott. Locate the door light switch on the fram of the oven door. Manually hold the light switch down and restart a clean cycle, once it begins cancel the cycle. This should send a signal to the motor to retract the lock. The clean cycle does not really have to start, you just have to make the oven go through the steps of starting and cancelling it. Hope this helps! Read More...
Robert F. March 18, 2011 for Model Number Jer8850AAW How can I release the oven door lock? It appears to have locked as we were replacing the glass top. It is F9 warning. We may have solved the problem but it may flip tight on us.
1 Answer Robert, if you were able to manually unlock the door and now have the F9 fail code. You can try unplugging the power cord or turn off the breaker for a few minutes and power it up again. Program a self clean cycle and cancel the selection after a few minutes. The control board constantly looks for a proper circuit on the latch switch and will usually run the motor until it finds the proper circuit. Good Luck! Read More...