Allen March 10, 2020 for Model Number Jenn Air Oven JJW9530DDB When turning on my oven, I get an error code 4d21. tI tknow it's the fan but need to know what part to order. Thank you.
1 Answer Allen, The part you will need to replace is WP74008383. We also sent an email with instructions on replacing the blower fan. Read More...
Susan January 01, 2020 for Model Number JJW96227DDS30 Hi, I have a similar question as asked in the past...my Jenn-Air wall oven keeps coming up with error code 4d21, which apparently has to do with fan malfunction per earlier troubleshooting response. However, the model number referenced in that response is a bit different than my own oven's model number so I wonder if the fan replacement part has a different model number as well. I want to be sure I order the correct part. Thanks!
1 Answer Susan, the error code provided is in regards to the upper fan WP74008383 not rotating properly. It is recommended that the fan is checked for any obstructions before replacing this fan. Read More...
John September 16, 2019 for Model Number JMW8530DAS I've got this very rhythmic clicking coming from my oven. I think its the fan but I'm not sure. I have a video but not sure I can post it here. Any suggestions?
1 Answer John, Occasionally the cooling fan bracket can vibrate. Simple foam tape or some dampening material could resolve this. The other option would be the fan being the problem, possible bearings in the motor or some other issue. WP74008383 Read More...
Tjaws November 15, 2017 for Model Number JJW8630DDS I have error code 4d22 on my jean air Double wall oven on the lower oven. I see two different tangential fans, which one do I need for the lower oven? Do I need to remove wall oven from cabinet to replace this part or can I access it from the control panel without removing the whole oven? Thanks
1 Answer Hello Tjaws, The lower fan motor assembly is WP74008437 for the model provided. The service manual for the unit states the following: Lower Blower Motor NOTE: Requires removal of the unit from the cabinet. 1. Remove unit from the cutout, see “Removing and Replacing Unit” procedure. 2. Remove screws securing the rear top and rear bottom outer wrapper from the chassis. 3. Disconnect and label wire terminals connected to the blower motor. 4. Gently pull plastic wire harness ties from oven chassis, securing wire harness. 5. Remove back screws securing the back half of the upper oven chassis to the lower oven chassis. 6. Tip the back portion of the upper oven forward and place blocking material between the two oven chassis. 7. Remove screws securing blower motor assembly to vent assembly. 8. Replace and reverse procedure to reassemble blower motor. Read More...
Sara January 06, 2016 for Model Number JJW8630DDS My lower oven is showing error code 4d22. What part do I need to fix this?
1 Answer Hello Sara. No Reverse Airflow Fan rotation (no/low RPM). You will need to check the fan motor in the unit. Read More...
Joseph November 09, 2014 for Model Number JJW9630DDW My Jenn Air wall oven is showing error 4d21. Looking it up tells me low fan rotation error. What parts do I need? And what would be the cost?
1 Answer Joseph, The error code indicating the fan rotation error would mean that the fan is either bad or has build up in it that is not allowing it to rotate freely. You will want to pull the fan out and check for obstructions. If clear then replace fan part number WP74008383. Read More...
D. M. October 10, 2011 for Model Number jmw9530dab How do you replace the tangential fan. The oven, non-convection mode, sounds like a saw.
1 Answer Hi D.M. Remove Power. Remove door, (if needed) for accessibility. Remove control panel lower trim panel. Remove and unhook the control panel ribbon cable and electricial connectors. The fan assy. part # WP74008383, is bolted in the LT. Rear behind the control panel. Reassemble on reverse. Thank You. Read More...