Andrew July 02, 2015 for Model Number Estate TS22AF I have a Estate TS22AF and the push in compression fitting on the water filter housing has broken. So now the water line from the house wall to the filter housing will not say connected. Are you able to replace this little grey fitting or does the whole filter housing(part # 2186443) need to be replaced?
Daniel February 05, 2015 for Model Number whirlpool 437559 fitting How do I"m disconnect this fitting from the water line under the refrigerator?
1 Answer Hello Daniel, You will push the water line into the fitting and while holding pressure against it, push the ring around the water line the same direction. While holding the ring against the fitting, pull the line out. Before re-installing, make sure there is no ridge formed in the water line about 1/4 inch from the end of the line. This will prevent the fitting from sealing. To correct this issue, use a razor knife the cut the water line even with the ridge. To re-install, push the water line into the fitting until it bottoms. Push even harder and it will pop in about another 1/4 of an inch. To seat the fitting, pull on the water line without touching the ring around the water line. Read More...
Diane June 04, 2014 for Model Number 10657953700 Movers took the doors off the refrigerator to move it. From the front of the refrigerator, freezer door side, a water line connector was disconnected and lost. I need to replace the water line connector. Kenmore side by side model number is 106.579.53700 Is the correct part number AP2973545? Thanks!
Michelle May 06, 2014 for Model Number gi7fvcxxy00 I need to replace the water line coupling with part 4373559. Can I also use 241503901 fridgadaire part? It is less expensive.
Rm January 26, 2014 for Model Number 10651572200 Can I bypass water filter housing by connecting 1/4 hose and 5/16 hose together with a union connector?
1 Answer Hello RM. It is not needed to bypass the filter. Per Factory No By Pass Just Remove Filter. Read More...
Donald November 05, 2013 for Model Number ed5ghexnqoo There are two tubes running down through the inside of the refrig and they seem to be disconnected at the bottom .When the water dispenser is used water comes out of one of them.The refrig belongs to my father and he does nor have aclue as to what happened.There are also two tubes [one coming from the front ofthe refrig and one coming from the water valve] that are not connected.There are no connectors or unions at the end ofthe tubes.Please Help
Brian T May 10, 2013 for Model Number Whirlpool Refrigerator ED5SHAXMT00 I purchased the machine used and need to connect the water to the unit. There is a severed grey tube on the back of the refrigerator. I need a kit to connect my copper tube (I believe it's 1/4 inch) to the grey tube. Which part number?
1 Answer Brian, You will need to replace the tube on the unit part number W11496481. This tube will have a 1/4" connector on it to connect to copper tubing. Read More...
Bryan L August 11, 2012 for Model Number WHIRLPOOL ED2GTQXKQ00 Does it have a water filter I cant find it in any diagrams and dont see one in the bottom grill or inside refrigarator?
Tony May 27, 2012 for Model Number Kenmore Coldspot 106.58139700 Severed water line going to fridge. No luck finding a good fitting to join the new 1/4 inch line without it leaking or splitting the new tube. Any easy joiners available that are idiot proof?
1 Answer Hello Tony. If the line is nylon water line, you can use a 1/4 X 1/4 fitting WP2198677. Read More...
Kala March 13, 2012 for Model Number AP2973545 I bought this fridge well ice maker does not have water. A local appliance store said I needed a tubing couplier 2 ends. I dont seem to understand how to put this couplier in?
1 Answer Hello Kala. For this coupler WP4373559, you will press the 5/16" line into the large hole until it locks into place and then press the 1/4" line into the small opening until it locks into place. These are compression fittings. Hope this helps. Read More...