Mary January 08, 2021 for Model Number WTW6500WW1 Turning wash cycle to normal and starts and quits. All right side cycles do that. The left side works. Could this be the Main Control Board?
1 Answer Mary, It would be recommended to get the tech sheet from inside the cabinet of the unit and put the unit into a service diagnostic mode to see if there are error codes. This will most likely be a control board that is faulty but would be best to see if there are errors. Read More...
Jeffrey March 07, 2017 for Model Number WTW6800WW! What receptical does the blue wire go on the right top of the Electronic Control Board, the choices are Flash Cntrl, Wide, Red and Blk. The unit spins but no water is going in. I've replaced the original board with a remanufactured one and the problem still exists.
Hilmar August 11, 2015 for Model Number Washer Whirlpool Cabrio wtw 6800ww Hi I need help, for example, if I put my washer on normal cycle (preset time 41 minutes) all of the sudden timer jumps to 5 minutes remaining time and changes the cycle on it's own. Hilmar
1 Answer Hello Hilmar. Based on the information you provided, it sounds like the control board WPW10249237 is bad and will need to be replaced on the unit. Read More...
J.M. May 06, 2015 for Model Number WTW6800WW1 My washer doesn't fill all the way up and goes to spin cycle over and over no matter what place you set control. There are no error codes flashing.
1 Answer Hello J.M., You should first make sure the standpipe is higher than the main top of the machine and is not sealed with tape or anything that would prevent it from getting a "burp" of air to prevent siphoning. Another thing that will cause this issue is if the drain line is pushed into the standpipe until it is actually under water in the standpipe trap. Read More...
Jr March 26, 2015 for Model Number whirlpool wtw6500ww1 During wash on Whirlpool Cabrio, everything went dead. No power to the control panel. Checked power thru cord to panel. Checked ok but nothing coming out to light up codes. Just blank and no light showing for anything. Don't know if the panel or the board is bad.
1 Answer Hello Jr, This sounds like the board WPW10249237 has failed. Be aware that a bad component on the machine could have caused the issue just as a brownout of the power could cause it. The two most common causes on the unit is the drain pump W10536347 and/or the motor rotor position sensor WPW10178988. Read More...
Susan H March 15, 2014 for Model Number wtw6500ww1 Our power went out 2 nights ago with surges before going completely out. Now our washer will not even turn on. Can you help me please.
1 Answer Susan, With the unit going out during the power surge and not coming on, first check the power supply. If the power supply checks ok then the most likely the main control board that is causing the issue with the unit. Read More...
Lenore April 11, 2013 for Model Number wtw6500ww1 Have a Whirlpool Cabrio its giving an F51 code. I replaced the RPS sensor and I am still receiving the code. Any ideas?
1 Answer Hello Lenore. If the sensor is new, you will need to order and replace the wiring harness on the unit. Read More...
Ddf March 17, 2013 for Model Number cabrio Washer filled with water and does not go through cycles. It just sits with water in it. The controls just flash. I am unable to turn it off unless I unplug the machine.
1 Answer Hello Ddf, This sounds like a bad RPS or a bad main control. You need to run the self-diagnostics and see what codes the unit is holding. This is explained in the tech sheet fastened to the inside of the front panel. Read More...
Anna December 24, 2012 for Model Number wtw6500ww1 The machine the only do is sprint the panel doesn't recognizes other funcion and doesn't give an error code.
1 Answer Hello Anna, If the control panel is not responding then you either have a wire connection issue or bad control panel WPW10249219. Read More...
Robert V January 17, 2012 for Model Number wtw6500ww1 My washer doesnt go threw a full cycle it reads f 51 as a code. What part would I need for that code?
1 Answer Hello Robert. F51 is a motor sensor error. Check and make sure all the connections are good and none of the magnets are cracked. If not, replace the stator on the washer to repair it. Hope this helps. Read More...