Jim October 19, 2016 for Model Number ATW4475VQ1 Water starts to fill tub good for 10 to 15 sec then starts filling @ a very slow rate maybe a hour to fill and starts washing never fills full force.
1 Answer Hello Jim. You will need to order WPW10144820 for the part that is needed for the unit if the water pressure coming to the unit is good. Read More...
Maureen T June 13, 2016 for Model Number Roper Washing Machine Model RTW4440VQ2 My washer does not fill completely up when on the super load. I have watched your videos and I believe the part I need to fix the problem is Switch-WI for $52.27. Can you possibly verify this is the correct part I may be needing? Thanks for any help! Maureen
1 Answer Hello Maureen. If the water level switch is bad, you will need to order and install WPW10231403 onto the unit. Read More...
Gloria July 01, 2015 for Model Number ETW4400WQ1 I select warm temperature only hot water comes ,I put on rinse and no water comes. I have no cold water.
1 Answer Hello Gloria. Make sure the screens are not clogged. If not, you will need to replace the water valve on the unit. Read More...
Joe January 27, 2015 for Model Number RTW4100WQ1 I have a washer machine that seems to get stuck in the rinse cycle every now and then. I left my house and returned 7 hours later and it was still filling with water. Any thoughts on things I should check or what you believe is going on?
1 Answer Hello Joe. It sounds like the unit is siphoning out the water in the unit. Check and make sure there is only 6" of drain hose in the drain pipe. Also, make sure the drain pipe is 36" off the floor in height. You will need to check and make sure the drain hose has an air gap going into the drain pipe. If it is air tight, it will siphon. Read More...
Dave December 19, 2014 for Model Number ETW4400WQ1 the water level rotary selection dial is stuck in the smallest load position. It simply will not turn. Does this mean replacement of the switch (~$50 part), and how complicated is the replacement if this is the cause? Washer is 15 yrs old and otherwise works ok still. Thks
1 Answer Dave, If the switch WPW10231403 is jammed and can't be dislodged, it will need to be replaced. It's not too difficult a repair to make, remove power to the washer. Remove the two screws in the back of the end caps and flip the console up. Disconnect the air tube from the switch assembly, disconnect the wire harness. Use a small flat blade screw driver to press the locking tab in, where it mounts to the bracket and turn the switch assembly to the left(counter clockwise) until it unlocks from the bracket. Reverse the process with the new switch and check it for operation. Read More...
Frank December 11, 2014 for Model Number Admiral Washer ATW4475VQ Water keeps filling the tub even after the agitator starts and even in the rinse cycle it will continue to fill after it start the rinse cycle. But if you close the water valve to the washer and turn it back on it will not flow into the washer.
1 Answer Hello Frank. Based on the information you provided, it sounds like the water valve WPW10144820 is bad and will need to be replaced on the unit. Read More...
Joshua January 18, 2014 for Model Number Estate Washer ETW4400WQ1 No Water, only Spin Cycle runs with Lid closed, 1st sent question about Switch-WI, response replace Timer. Timer replaced NO FIX, talked with Berry, said replace Lid Switch or call back. Talked with Nate, said Water Inlet Valve, replaced NO FIX - NEED HELP !
1 Answer Hello Joshua. If you remove the hose from the side of the tub assembly and blow into it, with the machine on, does it start agitating? If so, you need to check and see if the pressure switch is sending power to the valve. If not, it is the pressure switch WPW10231403 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Charles January 11, 2014 for Model Number Estate Washer ETW4400WQ1 My sons washer runs only in spin cycle, if he sets it at the start of a wash cycle, all it does is spin...wondering if it is the Switch-WI ?
1 Answer Hello Charles. No, based on the information you provided, it sounds like the timer WPW10199989 is bad and will need to be replaced on the unit. Read More...