Deepcoveoven November 09, 2023 for Model Number KEBS177SBL00 Our wall oven recently has been difficult to start. Pressing most of the buttons on the control panel work as expected - eg. pressing "bake", "convect", "easy convect", "self clean", etc.. all work fine to pull up the appropriate programming on the display. Pressing "On" however does nothing. In addition, pressing some buttons results in unexpected responses. Pressing "Oven Light" results in a Convect/Roast program coming up. Pressing "7" turns the oven light on. Pressing "7" again turns the oven light off. Pressing the "On" buttons does nothing or seems to send a 1 or 7 digit to the display. Would you recommend replacing AP6019275/WPW10312207 or do you think touch panel (item 4) on the expanded diagram for this model) is likely the culprit? Thank you!
1 Answer DeepCoveOven, based on the information provided, the control panel WP8303879 would be the cause of failure. Unfortunately, this part has been discontinued by the manufacturer and is no longer available. Read More...
George Kubes February 12, 2022 for Model Number KEBS107SSS04 Oven will not turn off after use. Heating elements remain on even after pushing the STOP control Appears to work for a while after turning off the main circuit breaker on main panel.
1 Answer George, Thanks for the question!!! The issue is being caused by a relay on the appliance manager sticking. The appliance manager is WPW10119143 and needs to be replaced. Read More...
Joan December 30, 2021 for Model Number KEBS107SSS04 with the oven on bake at 350 it will preheat to 329 and will not go any higher with oven on convection bake it preheat to 350 and works fine
1 Answer Joan, the oven sensor WPW10131825 would need to be tested for resistance. If it measures close to 1080 Ohms (between 1070 to 1100 at 77°F to 89°F) at room temperature, it is good and the most likely failure would be the relay control WPW10119143. Read More...
John December 29, 2021 for Model Number KEBS107SSS04 oven does not heat up to temp on bake but in will in convection bake
1 Answer John, the bake element WPW10207398 would need to be tested for resistance and it should measure between 26 to 30 Ohms. If it tests good, the most likely failure would be the oven relay control WPW10119143. Read More...
Suzanne October 28, 2020 for Model Number kebs107sss04" we replaced the board but it is asking for the cavity size how do we know what this is - "30" was the default
1 Answer Suzanne, If you measure the size of your oven example if it is a 27" wall oven then this will be the cavity size. Read More...
Larry August 10, 2020 for Model Number kess907sbboo l need a electric control board for my stove.it reads replace ui.then enter probe temp?i have tryed to reset it ,no go
Billy January 31, 2019 for Model Number KEBS107SS04 Oven will not heat to setting. What part or parts should I order and will there be installation instructions?
1 Answer Billy, If the oven temp. is high, low or erratic, and there are no error codes in the display, the more common problem is usually an oven temperature sensor WPW10131825 has lost it's calibration and isn't supplying the proper circuitry to the control. There are no instructions that come with the part, but there is a video attached to the parts diagram that should be helpful. Thanks, Read More...
Judy December 22, 2018 for Model Number KEBK171SSS04 Oven would not heat to temperature. We replaced the temperature probe, element and the control board. When we powered it back up they accidentally set the control board to the 30" model settings. The oven still does not heat to temp and we cannot figure out how to reset the control board to the 27" m o del settings. Oven is a single 27" wall oven no convection settings . Kitchen aid
1 Answer Judy, to program cavity size, disconnect power to oven, wait at least 10 seconds, reconnect power, enter diagnostic mode by pressing OFF, OFF, START. Press key #6 to show cavity size select screen. To edit, press CLOCK key. Scroll through cavity sizes by pressing key #6 until required size is displayed. Once correct size is displayed, press the START key to accept modification. Read More...
Shannon January 31, 2018 for Model Number KEBS107SSS04 I am seeing a F1E0 replace oven UI error code on my unit. I have disconnected power and still the issue persists. Is this the board I need to replace?
1 Answer Hello Sharon. The code means. Replace oven userinterface 1. Unplug oven or disconnect power.2. Replace the user interface WPW10312207.3. Replace all parts and panels before operating.4. Plug in oven or reconnect power. Read More...
John July 13, 2015 for Model Number KEBS109BSS00 There is power going to the oven but the oven is completely powered off. No LCD light on the screen. The screen is blank. What will be the potential cause? Thanks,
1 Answer Hello John. You need to test and see if there is power coming to the control board on the unit. If so, and the board does not work, you will need to order and replace the board on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...