Jim September 18, 2021 for Model Number KESH307HBL3 The left rear burner infinite control switch has failed. I have searched the internet and made a call to KitchenAid direct and come up empty. Nothing available. Is there an alternate switch available? if not I'll have to work with just 3 burners I guess. Thanks
1 Answer Hello Jim, I'm sorry but this part WP9751364 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Thank you for your patience and understanding in this matter. Read More...
David October 03, 2019 for Model Number KESH307GWH1 Right front burner (1800 watt) will occasionally (once or twice a month) stay on, glowing red continuously, burning the food. Turning off the element and turning back on corrects the problem. Is the a switch issue?
1 Answer David,It is possible that this is an early warning sign of contacts sticking in the infinite switch. The problem is you will not be able to test for failure until the failure occurs. It would be a safe bet that your switch is the issue if you wanted to go ahead and replace the part. Read More...
Sean September 03, 2017 for Model Number KESH307BBL6 The power on indicator light for the Right Front burner stays on even if the burner is not on and the stove top is cool to touch. I noticed this after a power outage. I also noticed some burn marks after I turned the breaker switch back on probably because the leads were resting on the metal housing after I dismantled the top control panel. The burner turns on and off fine after the short but the power light still stays on. There is continuity between the 4-H2 lead and the depressible arm in the off position and continuity between the 5-L2 switch and the depressible arm in the on position. Any suggestions? The part number for the switch is 9751363 (Kitchen Aid Superba Stove Top)
1 Answer Sean, The part that would cause this issue will be the infinite switch which would be part number WP9751363. Read More...
Harry January 09, 2017 for Model Number KESC307BWH3 Switch # WP9751363, I have replaced the switch and it still does not work. The power lite is all that comes on. Is there anything other than the switch that may need attention?
1 Answer Harry, If the burner is not coming on then you will want to check the wiring between the switch and the burner and if it is ok then it would be the burner that is the issue. Double check to make sure that you have power to the switch and out of the switch. Testing power you will want to check across L1 and L2 for 240 vac and then with the burner in the on position check for 240 vac from H1 to H2. If these both check ok then proceed with checking wiring and the element. Read More...
George February 19, 2015 for Model Number YKESC307GS1 I had the *exact* same issue as Josh from previous question: saw a spark from FR burner switch and now oven doesn't work due to short circuit. I found a wire melted off the burner switch, but I tested the switch for continuity and it appears to be fine. SO how can I repair my existing wire or identify those connecting wire parts and order a new one? They are not found in my parts diagram. Thanks!
1 Answer George, The wire harness has been discontinued for the unit but you can use a hi temp female spade connector to cut and splice the terminal. Read More...
Scott March 03, 2013 for Model Number kesh307gwh1 The serial no. 1mh5032785 . The kitchen aid 30" slide in has a problem with the front right halogen burner. It first started with the burner switch on/off light not shutting off unless you flicked it a couple of times. This was intermittent, but now when you turn the burner on the switch light goes on but the burner doesn't turn on and heat up. What are the part #s for the halogen burn and does it come with the limiter and the switch. To test the limiter and burner can that be done by continuity? The switch by volt meter? Thanks Scott
1 Answer Scott, To test the limiter you would want to check resistance and to check the element continuity. The switch you would check voltage. The element part number is W10155788 which is showing as being discontinued by manufacturer. Read More...
Rob January 19, 2013 for Model Number YKESC307HS4 The front right burner stopped working. Is this the 1800W element?
1 Answer Hello Rob, You are correct. On your unit, the elements are catagorized like this: Element, Surface (1000/2500W - LF) Element, Surface (1500 W - LR) Element, Surface (1800 W - RF) Element, Surface (2200 W - RR) Read More...
Thomas R. April 09, 2012 for Model Number KESC300HBT4 Is the infinite switch 1800w suitable for a dual element burner?
1 Answer Hi Thomas. No the switch part # WP9751363 mentioned does not work with the dual burner on the front left of your unit. You need switch part # 8203536. Thank You. Read More...
Josh October 02, 2011 for Model Number KERC607EHW5 Range The switch on the right front burner was loose and in trying to play with it, I caused a spark. This caused the whole oven to turn off. I had to switch the breaker back on, but the oven still doesn't work. Do I just need a new switch or is this a bigger problem?
1 Answer Hi Josh. Remove power. Yes you will need to replace the switch as you have internally shorted the device. Part # is WP9751363. While you are in there always repair all loose connections and inspect the rest of the wiring. Thank You. Read More...
David April 07, 2011 for Model Number KERC607HBL6 I understand. Is the switch a likely problem here (switch light turns on but burner does not heat.)? Thanks!
1 Answer Hello David! If the element has already been replaced and it is still not heating, then the switch would be at fault. Thanks. Read More...