Matt March 06, 2015 for Model Number Maytag SAV365ZAWW I load up the washer , it fills with water and agitates like normal and then stops , and doesn't drain.. I have to reset the cycle and it then drains... FYI ., i replaced the timer... Please Help
1 Answer Matt, With the unit sticking going into the drain cycle you will want to the voltage going to the motor on the spin cycle. If it drops below 108 vac then the issue will be with either the wiring or supply voltage. If the voltage is normal then the issue will be with the switch on the motor. Read More...
Wendy January 15, 2015 for Model Number SAV365ZAWW My Washing machine fills with water and washes fine but when it gets to the spin cycle, it stops and make a clicking sound. I have to turn the knob to the rinse cycle. After the last spin , sometimes the water is left in the machine. Do you think this could be the timer?
1 Answer Wendy, The timer WP27001113 is the more likely issue. Before you replace it, you also need to check the drive belt and idler assembly, to make sure there's no excess drag on the motor when it tries to start the spin/drain cycle. Read More...
Lisa April 04, 2013 for Model Number Maytag SAV5910EWW Washer starts, fills and agitates fine but clicks off as soon as it hits the rinse cycle ande doesn't come back on. It does this in all 6 wash settings. Would this more likely be the lid switch or timer or something else?
1 Answer Lisa, You will want to check to make sure that the cold water fill screen is not clogged. If it is clogged then it will cause the unit to not fill with water. The lid switch will not allow the unit to agitate or spin if it was bad. Also check to make sure that there are no kinks or clogs in the air dome or pressure hose. Read More...
Delia March 28, 2013 for Model Number sav2655aww The washer fills with water and then it won't do anything else. Is that the timer switch? It is just dead after it fills up.
1 Answer Hello Delia. The first thing you will want to check on the unit is the lid switch assembly 40034901P. If bad it will cause the issues you are having with the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Don May 12, 2012 for Model Number SAV2555AWW When filling washer the water does not stop I have to tur off water to the washer or it overflows.
1 Answer Hello Don! If you run the washer and unplug the unit does it continue to fill with water? If so, you will need to replace the water inlet valve part number WP27001146. If the unit stops filling you will need to check the water pressure hose to make sure it is not kinked or clogged and replace the pressure switch part number WP27001203. Hope this information helps you, thanks! Read More...
Don April 11, 2012 for Model Number sav365zaww The washer fills fine but will continue to agitate through the whole wash cycle (until hits off) but if I lift the lid and re-close it machine will go ahead and start where the timer is showing - example: if I lift and close lid at the rinse cycle, it will go ahead and drain and then fill up again for rinse but continues the rinse agitation until I stop it or if I lift the lid at the spin cycle, it will drain & spin. Also once in a while, after washing a load the machine will stop working at all for a couple of hours no matter where I set the selector and then next time I open & close lid it will start working again.
Evan November 24, 2011 for Model Number SAV4655EWQ Sometimes it works fine. Other times, it fills, agitates, then will stop mid cycle. Other times, it will cycle through, but what the control dials indicates is happening (ex. rinsing) is not what in fact is going on.
1 Answer Hi Evan. It sounds to me you have a faulty water valve part # WP40107001. Make sure your water hoses are flushed out in a bucket before you change the valve. The cold water side will be plugged up and wont allow the rinse fill cycle. Thank You. Read More...