Chuck March 18, 2022 for Model Number Jenn Air JDS9860AAP I Believe I may have a bad rocker switch for the fan speed as ithe fan runs at the same speed whether the switch is toggled up or down. I will order the switch number previously provided but need to confirm that this symptom indicates a bad switch. Also, do you have instructions on how to remove the old one and install the new? Looks like the two screws on each side of the control panel must be removed. I presume it then comes off the range body? Or does something else need to be disconnected? Or can it be popped out from the front? One person in the comments said they did that using a putty knife. Thanks.
1 Answer Hello Chuck, As per the manufacturer: 1. Remove power from the unit. 2. Remove burner switch control knobs. 3. Open oven door and remove screws securing control panel. 4. Remove screws located on the right and left sides of the control panel. 5. Grasp control panel on the far left and right sides and gently pull the control panel out and down. NOTE: Gently pull control panel out and down. 6. Remove infinite switch control knobs, infinite switches, indicator lights, rocker switches, and electronic control/clock (as necessary) and transfer to the new control panel. 7. Reverse procedure to reinstall control panel. Read More...
David July 29, 2016 for Model Number SVD48600P How do you access and remove the old exhaust switch? Do you have to remove the knobs, bezels and control panel cover? Is it wired by user or plug in?
1 Answer Hello David. Yes, you will need to remove the knobs, bezels and the control cover to access and replace the switch. The wires have terminals you can pull off the old switch and slide onto a new switch. Read More...
Sam July 01, 2016 for Model Number SVD48600P Jenn-air gas-electric grill-range model #svd48600p rocker exhaust fan switch removal/replacement?
1 Answer Sam, If you could provide a email address we should be able to provide more information on this unit. Read More...
Dave February 07, 2016 for Model Number Jenn-Air Dual Fuel slide in range I just replaced the 3 way fan switch (AP3024740). The fan still will not stop. It runs at low speed at all times and speeds up to high speed when the gas is turned on. Any idea what to do next?
1 Answer Hello Dave, If you could please provide the model number from the units' I.D. tag, we can try to pull some specific wiring information s we can assist in the troubleshooting of your unit. I'm sorry but this is the only way we can provide proper assistance. Thank you for your patience and understanding in this matter. Read More...
1 Answer Hello Anthony. You will need to test the switch for continuity. NC to COM should read closed and NO to COM should read open. This will reverse as you press the switch. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Anthony G December 28, 2015 for Model Number SVD48600P HOW do I wire terminals 1,2, and 3 ON this rocker sw # 5
1 Answer Anthony G,, The Orange wire will connect to terminal 1, the white to terminal 2 and the brown to terminal 3 on this switch. Read More...
Walt March 03, 2015 What are the dimensions of this switch. Need the opening dimensions that it will fit into. I have a JennAir with a switch for the light and fan 1811-9913 that I am looking to replace
1 Answer Walt, The rocker switch WP3147265 appears to be about 1 1/4" x 3/4" opening size. Read More...
Bruce B December 27, 2013 for Model Number Jenn Air SVD48600P Is this replacement switch (#5) that you offer an ON-OFF-ON switch for a two-speed fan? If not, It's not compatible.