Matt April 25, 2021 for Model Number MAH6700AWW Hello, my washing machine MAH6700AWW is showing a tE code. I have cross referenced the error and found that it is the sump thermistor (Part #34001202) which is no longer available. Is there another part number for this that I can use for a replacement? Thanks
1 Answer Matt, Unfortunately, with the thermistor having been discontinued by the manufacturer, there would be no suitable replacement available. Read More...
Susie October 26, 2017 for Model Number WFW9550WW00 Had error code F24. Replaced temperature sensor. Error code continues to pop up less then a minute starting machine. Doesn't matter what water temp using. I unplugged and waited 1/2 hr hoping machine would reset control panel. What do I need to check next?
1 Answer Susie, Since you've replaced the sensor, the next check is the wiring connections where they attach to the sensor. It's not uncommon for the wiring to fray and/or loosen at the crimp joint where the terminal and wire are attached. You can also check the resistance of the temperature sensor at the SET2 (pins 1&2)connector on the CCU. If the resistance is in range, and there's no issues with the wiring or terminal attachment, then the problem would be in the control board/CCU. Read More...
Pam September 20, 2016 for Model Number WM3050CW My /LG Front Load Washer had a tE code. My husbands soldered the wires & put back in the Thermistor. Now the code PE is showing and the door is locked. Am I needing a water level sensor also?
1 Answer Hello Pam, You should check the pressure sensor hose for clogs and/or kinks. If no issues are located and the harness is good, the issue can be in the pressure switch 6601ER1006G or the control EBR78534104. Read More...
Cheryl June 22, 2016 for Model Number NFW7200TW During the last spin it coded tE. Any idea what the problem could be?
Raymond March 25, 2016 for Model Number Wfw9151ywoo whirlpool washer Is the thermistor and the water temperature sensor, do the same job?
1 Answer Raymond, Yes the thermistor is the same them as the water temperature sensor and is part number WPW10467289. Read More...
David July 05, 2015 for Model Number WD8704DJA Hi - I live in Asia and it is very hard to get decent, knowledgable support here - so I am posting here to help troubleshoot the issue and narrow my part replacement. My Samsung washer/dryer combo is getting error message HE2 - which is the heater element for the dryer. Since there is only one heating element (not one for hot water and one for there dryer) I tested both the heater element and the thermistor. The heating element is registering 27 ohms - which should be OK (yes?) and the thermistor is registering 8K Ohms at ambient temperature (which was about 95 degrees F the day I tested) but my research indicates that the thermistor should be ~20K Ohms - twice that for USA/120 VAC models - which indicates to me that my issue is the thermistor - am I correct? Can you supply a new thermistor for a 220VAC machine?
1 Answer David, Unfortunately we would not have the parts required for your unit but it does sound like the issue will be caused by a faulty thermistor. We do not have the technical information on the unit to know the exact range of what the thermistor should read for your unit but 8K ohms at 95 degrees ambient does sound like it would be off and the thermistor would need replaced. Read More...
Renea April 29, 2015 My whirlpool front loader washer stops and beeps in the middle of the cycle and wont complete the cycle. Someone said temp sensor was bad! What is that and are they correct??
1 Answer Hello Renea. We will need your model number and any error code the unit is giving. Thank you. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Ahmed E April 24, 2015 My Samsung front load washing mashing heater keeps working even if "cold" is selected. The thermistor is 34001202, but I wanted to be sure that the thermistor is the one responsible for making the heater working all time. please advise
1 Answer Ahmed, The most likely cause for the heater to stay on all the time with any cycle selection would be that the relay on the control board is stuck and the control board would need to be replaced. Read More...
Shirley November 21, 2014 for Model Number NFW7200TW I cannot change the water temp on my Amanda front load washer. It is stuck on hot/cold cycle. What do I need to fix this problem.
1 Answer Hello Shirley. If the board is stuck and does not change in any cycle, you have a bad control board WPW10273828. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
William April 28, 2014 for Model Number nfw7200tw There is no power to the machine but power at the receptacle.
1 Answer Hello William. If there is power to the control board WPW10273828 and it does not come on, you will need to replace the board in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...