Barry October 30, 2018 for Model Number ED25TQXFW01 I replaced the defrost timer and put the black jumper on number two. Ran fine for a few days and then iced up on coils. I replaced the thermostat unit as it was rusted. Refrigerator is now running and cool, but not going into defrost mode. (Not sure if it was defrosting when timer first installed) I manually advanced the timer by using the spindle on the bottom and it goes into defrost. I checked the heating coil and it heated up. Any suggestions? Also, two additional questions: 1. How long does this timer run between defrosting? 2. How long should frig run normally between pump cycles? Thanks!
1 Answer Barry, make sure your defrost timer plug has the following colored wires going into the timer, black, pink, red, orange. If you don't have these colors, the black wire will need to go to the #1 terminal, just a thought. Read More...
Richard B. October 30, 2018 for Model Number ED25RFXFW00 I am replacing the defrost timer and need to know what pin to place the black wire on.
1 Answer Hello Richard, You will need to connect the black jumper lead to the number 1 terminal on the model provided. Read More...
Mike October 29, 2018 for Model Number ET8WTMXKQ05 I bought a defrost timer part number PS11723171 for my fridge model number ET8WTMXKQ05 from your online store. My old timer has the following configuration order: 2 (Pink) - 1 (Orange) - 4 (Red) and the last one 3 (W). Where should I connect the black pin to? Is it #1 on the new timer? Thank you.
Olathe Diy October 23, 2018 for Model Number 10653332300 Got the defroster timer for my kenmore refrigerator model no 106.53332300. Sería la no. SR0934242 but the parts don’t look like alaike at all. I see the 4 prone connector but there is 2 more plugs . How do I install it
1 Answer Olathe DIY, The model is showing it has an adaptive defrost control board on it and not a timer. The part number that you would need for your unit would be WPW10366605. Read More...
Barry October 22, 2018 for Model Number Whirlpool ED25TQXFW01 Which pin does black wire go on? Current configuration: Pin 1: Orange Pin 2: Pink Pin 3: White Pin 4: Red
1 Answer Barry,You have a cumulative run timer and the black wire goes over number 2 on the very end. Read More...
J October 02, 2018 for Model Number ED25SMXRWR0 I got the replacement defrost timer for my whirlpool ed25smxrwr0. It has a black lead the original does not. Where does this connect? Thanks in advance.
1 Answer J, You would follow the wiring instructions for "procedure 2", " push slotted loose timer motor lead over & all the way down terminal number 2 with wire toward timer motor Then attach the wires to the terminals " #1 – Black Wire #2 – Pink Wire #3 – Red Wire #4 – Orange Wire ". Thanks, Read More...
Paul B September 29, 2018 for Model Number Kenmore coldspot 106-60834102 I bought defroster timer W10822278. Could you please tell me which pin to attach the black wire to? Thank you
1 Answer Hello Paul, if your unit has the following color wires black, pink, red, and orange the black wire for the timer motor will go on terminal 2. If your unit has orange, pink, white and red the wire will go on terminal 1. Hope this helps! Read More...
Lynn September 23, 2018 for Model Number 106.57362700 Could you please tell me with defrost timer W1082278 which terminal I put the black lead on. I have a Kenmore Model No. 106.57362700 Thank You!
Pat J September 22, 2018 for Model Number Frt045gb How do you make a fap part #483212 defrost timer work for this frig? Compressor will only come on in defrost cycle
1 Answer Pat, Unfortunately we do not have any information on this model refrigerator but the defrost timer that you have for this model will not be the correct on for the unit. Read More...
Jeff H. September 12, 2018 for Model Number Whirlpool ETOMSRXTQ00 I didn't receive any instructions with the timer that I ordered (W10822278) for my Whirlpool refrigerator (model no. ETOMSRXTQ00). Am I correct in assuming that the black wire goes to terminal number 1. The old timer is marked "bk" on terminal no. 1
1 Answer Jeff, based on the model number you supplied the refrigerator has a "version 1, Cumulative run application for the defrost timer. to properly wire the replacement timer : first, push slotted loose timer motor lead over & all the way down terminal number 2 with wire toward the timer motor. terminal 1, will have the Black wire attached. Terminal 2, will have the timer motor wire and the Pink wire attached to it. Terminal 3, will have the Red wire attached to it and the #4 terminal will have the Orange wire attached to it. Read More...