Tango June 13, 2018 for Model Number KTRC20KBWH00 When installing defrost timer p/n 482493, where does the black wire go?
1 Answer Tango, The black lead wire on the defrost timer will go to terminal number 2 for your unit. Read More...
Ken June 13, 2018 for Model Number RT21LMXKQ04 have no wiring diagram, need to know what terminal the black wire goes on for install of new defrost timer.
1 Answer Ken, For your unit you will put the black lead wire onto the terminal number 1 of the timer. Read More...
Barry June 10, 2018 for Model Number Whirlpool ED22PWXXWOO refrigerator I'm replacing the defrost timer (AP5985208) on my Whirlpool ED22PWXXWOO refrigerator. Which terminal does the black lead connect to?
1 Answer Barry, In your case, the loose, black timer motor wire lead is attached to the number 2 terminal. "For cumulative run timer push slotted loose timer motor lead over & all theway down terminal number 2 with wire toward timer motor" Once the timer motor lead is installed, the remaining wires should be installed on terminals as follows: term. 1 – Black Wire. term. 2 – Pink Wire, term. 3 – Red Wire and term. 4 – Orange Wire. Read More...
David June 04, 2018 for Model Number 1068627482 I do not have the wiring diagram for this refrigerator so I do not know if this is a version 1 or version 2 cumulative compressor run application. I have the defrost timer but I do not know where to install the loose timer motor lead. Thanks My Kenmore Model is 1068627482 Thank you
1 Answer Hello David, you have version 1 and the black motor wire connects to lead #2. Hope this helps! Read More...
Errol June 01, 2018 for Model Number Whirlpool Model EV190N ( 190NXSN01 ) UPRIGHT FREEZER EV190NXSW01 I ordered a replacement defrost timer w1082278 and received it a week ago. I did not receive installation instructions explaining where to connect the black wire to which of the 4 terminals. the old timer 1115416 had a tab on the metal housing to connect the green wire ground and it had two black wires connected to #2 pink and #3 red. I taped off the green ground wire and connected the black wire on the new part to No. 2 terminal ( pink ) by my best guess. The freezer operates but will not get below 32 degrees (F). This is what had started happening with the old timer.
1 Answer Hello Errol, The black jumper lead goes on terminal number 1. The issue you are having does not sound like an issue caused by the defrost timer. You should check the frost pattern on the freezer coils. If there is an iceball where the lines come in through the back wall of the unit, there is a Freon loss. If there is no frost at all there may be no Freon in the sealed system at all or, if the compressor is hot, there could be a sealed system restriction. If there is frost built up heavily, the unit may have a defrost issue. Read More...
Kent May 28, 2018 for Model Number EHT201ZKNR5 For this defrost timer, what \terminal do I need to use for my Whirlpool model EHT201ZKNR5 refrigerator?
1 Answer Kent, If your wire colors are black on 1 pink on 2, red on 3 and orange of 4 then the jumper wire will go to terminal 2. If the wire colors are orange to number 1, pink to number 2, white to number 3, and red to 4 then the black lead will go on terminal number 1. Read More...
Chris May 26, 2018 for Model Number et18nkxfwo 1 Which terminal does the black wire from the defrost timer go to?
1 Answer Hello Chris, You will need to connect the black jumper lead on the defrost timer to the number 1 terminal of the defrost timer. Read More...
Germain May 24, 2018 for Model Number 106.70202991 I do not have the wiring diagram for this refrigerator so I do not know if this is a version 1 or version 2 cumulative compressor run application. I have the defrost timer but I do not know where to install the loose timer motor lead. Thanks
1 Answer Hello Germain, You will need to connect the black jumper lead to terminal number "1" for this application. Read More...
1 Answer Hello Ken, according to the diagram for the model number you've supplied you will want to slide the black wire on terminal #2. Hope this helps! Read More...
Tim April 30, 2018 for Model Number MTB1891ARQ Replacing the Defrost Timer (63001353) w/ new timer # 10822278. Which # lead should I hook the Black wire to..? Thanks! Tim
1 Answer Hello Tim. You will need to place the black wire onto terminal number 1 of the timer. Thank you. Read More...