1 Answer Tom, Yes, the WP3955489 / WP3955489 Timer, Control , is the correct timer to order for the model number you supplied. It is the Factory Direct Replacement part per the manufacturer. It may look different, but it will function properly in your washer. The part is in stock and available at this time. Thanks, Read More...
Dave October 07, 2015 for Model Number CAWS729MQ0 The timer stops when it reaches the point where the washer should drain or spin. It fills and agitates fine and also manually drains fine but will not automatically drain at the end of the wash cycle or spin cycle and will not spin. If I manually advance the timer it still will not drain or spin. How can I test to find out which parts are needed?
1 Answer Hello Dave. You need to test the lid switch 3949247V on the unit. If it is bad, the unit will not drain or spin. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jorge March 07, 2015 for Model Number LSR6332KQ0 Do you send to Mexico and how much is it for the package cost?
1 Answer Hello Jorge. Unfortunately, we are unable to ship outside of the US or Puerto Rico at this time. We will need a US physical address to ship parts to. Read More...
Eric August 12, 2014 for Model Number Inglis My washer will not drain, all other steps in the cycle seem to function correctly. The hose is not clogged since it does drain manually. I opened up the washer and found that both the pump and motor shaft turn without obstruction. I even removed the pump and tried the draining step, it seems that power isn't getting to the motor and I hear buzzing (maybe forcing) sound coming from the timer control. I'd order a new timer control but I want to be sure that it is the problem before forking out the money for it. Any tips on how to test this control would be greatly appreciated. Thanks!
1 Answer Hello Eric, If you hear a buzzing sound from the pump, it is most likely that the drain pump that has failed. I would list a part number but was unfortunately unable to look up a part since no model number was listed. Read More...
Rick July 12, 2014 for Model Number Whirlpool washer Is part number 3955489 washer timer the same as 3953196 washer timer?
1 Answer Hello Rick! We were unable to cross reference part number 3953196 to see if it was the same part as WP3955489. If you provide a model number we should be able to determine the correct timer for your unit. Thanks! Read More...
David July 28, 2013 I only need the black retaining rod that goes through the back side of the timer to hold the knob. Can I purchase just this part? The part number for the timer 3955489a.
1 Answer Hello David. No, sorry but you have to order the timer assembly WP3955489 for that part. Read More...
Ben January 02, 2013 for Model Number Don't know Whirlpool washer 6 cyl. commercial quility-super capacity , does not spin everything else operates. Could it be the timer or the coupling?
1 Answer Hello Ben, If the unit is agitating then it would not be the coupler. It could be a timer but if the unit has a clutch assembly you should check it first. Read More...
Hal November 24, 2012 for Model Number whirlpool lsr6332kqo My washer stops at rinse cycle. Even if we then move it manually it will not enter the rinse cycle on any of the different wash options.
1 Answer Hello Hal, I would test the cold water inlet valve 285805 first. If the unit is filling with rinse water but not agitating, I would look at the lid switch. Read More...
Dave April 15, 2012 for Model Number LSR6332KQ0 I had an earlier question involving the timer and the lid switch. I had determined that the faulty part was the timer because I had continuity at the switches plug. When checking to see if the lid put enough pressure on the switch, the switch fell apart. I don't have a wiring diagram but I know we have 3 wires, one is a ground. My question now is: Can I run a jumper between the 2 remaining wires and plug the connector into it's female connection. I would also hook up the the ground. Hopefully, this would allow the washer to think the lid was closed and I can see if it really was the switch and not the timer. Thanks, Dave
1 Answer Hello Dave. Yes, you can jump the lid switch 3949247V to test it, but do not continue to run the unit with the lid switch bypassed. If the lid switch is broke, it will need to be replaced. Hope this helps. Read More...
Dave April 14, 2012 for Model Number Whirlpool LSR6332KQ0 My washer quit just before the spin cycle. It has been suggested to me that the lid switch went out. I tested the lid switch and it shows continuity when pressure is applied. Could it be the timer? I have manually advanced the timer and it agitates and does everything during the first part of each different washing method(perm press, normal, delicate etc) and quits at about the same spot on the dial for each category.
1 Answer Hello Dave. Check and make sure the plunger is pressing the lid switch. If the lid switch is working properly, and you can manually advance the timer and the unit works properly, then you will need to replace the timer WP3955489 on the unit. Hope this helps. Read More...