Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Discharge Housing Assembly by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18029643
Manufacturer Part Number: WP6-917075

Dishwasher lower washarm drain pump housing.

More

Questions & Answers

For Whirlpool Discharge Housing Assembly (Part Number: OEM18029643)

Ed for Model Number MDBD820AWB

I am attempting to clean the pump area and check the impeller as the cause of poor cleaning. I have removed all down to the discharge housing as shown in your video. It appears that the housing is frozen or stuck to the impeller or there is a ridge of gunk that is preventing the housing removal. It is loose but will not yield to any amount of wiggling or twisting. Will it be best to cut it out for removal or is there a suggestion for a soak that may dissolve the gunk? Is it possible that a broken piece of the impeller could cause the jam? Thanks, Ed

1 Answer

Ed,

There are a couple of screws that hold the discharge housing in place and you will want to make sure that they are removed. If they are and it still will not come off then maybe put some vinegar down in there and let it soak to help it dislodge.

Read More...

1 Answer

Hello Dirk. You will need to check and see what is holding the housing in the unit. Look for bolts or screws.

Read More...

1 Answer

Floyd,

Try to run the unit through a wash cycle empty with some vinegar. This will normally neutralize odors. Also check the pump assembly to ensure that there is nothing caught in it and check the hoses to make sure that they are cleaned out.

Read More...
Rolf for Model Number MDB7130AWW (Maytag Dishwasher)

Washer will not clean. Fills and advances to wash cycle, but water does not spray. I suspect a problem with the impeller but am unable to access it. I can not remove the "Upper Discharge Housing Assembly. The three bolts holding down are removed. The housing moves up and down about 1/2 " and turns about 2 inches. The housing has a 1/8" X 6" inch gap around its perimeter, which may be the cause of not creating pressure. When I ran the machine on a wash cycle with just the upper housing in place and not bolted down, a plastic disk was expelled through that gap. Please help Rolf

1 Answer

Hello Rolf. Remove the screws and wiggle the part out. It might be a tight fit. This is the way it comes out of the unit.

Read More...
Jason for Model Number Maytag MDB6650AWB

My dishwasher fills but will not drain. When the drain cycle should be starting, I hear a brief hum from the motor, as if it is stuck. This will repeat unless I shut off the washer. I checked all drain hoses for blockage, and they were clear. I removed and inspected all parts down to the drain impeller for obvious signs of failure and found none. Could this be a faulty discharge housing assembly, or am I looking at a failing motor? Thanks for your assistance.

1 Answer

Hello Jason,


Make sure that you double check to make sure that there is nothing stuck in the pump assembly. If not then you would have to replaced your motor assembly 6-917112.

Read More...

1 Answer

Hello Craig,

The entire problem is with the discharge housing assembly WP6-917075. If that part that comes off can come off, it has to be replaced. When the pump spins, this part is causing the roar and since the water has to be forced through this parts fins, it cannot discharge correctly. Replace this part and the issue will be gone. The "o" WP99001326 ring should be replaced also. The overuse of soap and rinsing all of the dishes has caused the chemical reaction to attack the rubber and the "o" ring will never be right unless it is replaced.

Read More...

1 Answer

Hi Jd. Check the drain hose at the end where it hooks on the end of the sink. Put it in a bucket and press cancel or drain. Is it working? Clean all internal filters [part # is AP4112901] and wash arms. Check the sink drain to see if anything is clogging there also. Do you hear the pump? The pump/ motor is part # 6-915415. Thank you.

Read More...

1 Answer

Gardner, The discharge housing is not the issue. It produces pressure to the wash arms in the wash cycle. Apparently this is a Mayatg dishwasher and it probaly has a two direction motor, so do you hear the motor reverse and the pump attempt to drain ? Try disconnecting the drain hose from the displosal or air gap and see if it will drain, you may have an obstruction in the line. Thanks and Good Luck

Read More...

1 Answer

Hello Mark! Remove the screws and wiggle the part out. It might be a tight fit. Thanks.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google