Jack W July 10, 2015 for Model Number MDB6601AWS Removed vent, and the plastic switch that twists came out, once I reassembled the inner door and made my connections, the steam was not being dispelled like before out of the vent, the plastic piece did not seem broken, I put the rubber gasket back on and reattached. Do I need to replace the vent unit ?
1 Answer Jack, With the plastic switch coming out and the unit not opening to let steam out then you would want to replace the vent assembly WPW10190890. Read More...
Melvin January 18, 2015 for Model Number ADB1500AWW I took the vent housing assembly off, after noticing what looked like mold coming from the door vent, and it's sludgy (moldy?) inside. Does it need to be replaced, or can I just clean it and put it back? Is something clogged that is keeping moisture in there?
1 Answer Melvin, You can clean the part and replace and there is moisture that goes through the vent housing assembly during the dry cycle so there will be some moisture that can get trapped. Read More...
Amy January 15, 2015 for Model Number MDB7600AWW Our dishwasher is leaking from the upper left hand corner of the door. It seems as if the door doesn't seal correctly as you can hear a difference when you push on that corner. Can you help me?
1 Answer Hello Amy, While the door seal WP99002588 is probably partially responsible, it sounds like the door line may be warped a bit. You should loosen the screws around the door liner and hold the door level while tightening the screws. This will sometimes help the situation and prevent a new seal from having the same issue. Read More...
Rachel June 24, 2014 for Model Number MDB5600AWW My dishwasher gets water into the control panel. We think it may be leaking into the area through the vent but not sure. Is there any idea of how to fix this issue. It will get water into the control panel and short it out causing the dishwasher to stop. Once the water is dried out the dishwasher will turn on again.
1 Answer Rachel, Check and make sure the water is not too hot, the average water temperature in the tub should be 120 - 125 dgrs. F. This will allow the water heating options to operate properly without producing steam. Check and make sure the vent cover in the door is installed properly, the large opening should be pointed down towards the bottom of the door. When you remove the control panel, you'll find a foam gasket on the right side surrounding the vent openings in the panel, check and make sure there is an indentation in the foam where it meets the vent opening, if not add one or two seals WP99003222 to the panel, so there's a good tight seal between the panel and the end of the vent outlet. Lastly, check the door liner and outer panel to make sure they are attached to the hinge assembly tightly, and check the inner door liner to see if it is warped or "tweaked" and not sealing properly. Read More...
Nancy May 14, 2013 for Model Number mdbtt60aww2 I have replaced the vent, and the door seal and it is still leaking from the front, does the door seal need to be put in with a gasket glue?
1 Answer Hello Nancy, You should look closely at the spray arms. They will sometimes separate where they are put together at the factory and cause a surge of water to come from the side of them. This will put a wave in the water as the spray arm circulates. Stopped up holes in the spray arms will also cause the same effect. The door seal does not glue in. Read More...
Nancy May 09, 2013 for Model Number mdbtt60aww2 Can you get just the switch for this model, or do you have to buy the entire assembly. My dishwasher is leaking, I have replaced the door seal, and it still leaks so I am thinking that it is possibly the air intake switch.
1 Answer Nancy, The switch cannot be gotten as a separate part and has to be purchased as an assembly. Read More...
Rodney K. December 11, 2012 for Model Number Matag MDBH945AWW How do get the vent of off the inside panel of the door?
1 Answer Hello Rodney, The vent grille on the inside of the door holds the assembly to the door panel. To remove it, turn the grille about 1/4 turn. The vent assembly will drop off on the other side. Read More...
Jim October 03, 2011 for Model Number ADB2500AWW FOR THE VENT HOUSING ASSEMBLY WHICH WAY DO YOU CONNECT THE WIRE BACK TO THE TERMINALS. I HAD TO TAKE IT OFF TO REPLACE THE INTERIOR DOOR AND DIDNT NOTICE THE ORIENTATION OF THE PLUG(ONE WIRE ON ONE SIDE AND TWO ON THE OTHER). JIM
1 Answer Jim, The wiring locations, doesn't really matter, the wax motor for the vent is a simple switch configuration (power in / power out). Thanks and Good Luck Read More...
Brian G March 14, 2011 for Model Number mdbh965awq How do you know if the vent house assembly is bad? My dishwasher is blowing steam past the door seal. It doesn't appear the vent is exhausting any steam. Can the switch be tested?
1 Answer Hello Brian. Press heated dry 5 times, then press the start key within 8 seconds. The normal light will flash 3 times. If you press cycles select/normal one time the heavy wash light will come on, and the vent should open. If it does not open, then the switch is bad. It takes this a little time to open, about 30 seconds it should be moving. Hope this helps. Read More...