Jason March 19, 2014 for Model Number 10650259001 Can you tell me the model number for the right ice maker and wiring harness?
Donna December 17, 2013 My ice maker is not filling with water, I have another ice maker that is similar , but the wire are a little smaller. Will it be ok to splice them and connect them to the other harness with larger wires?
1 Answer Hello Donna. Sorry, we can not recommend altering parts to fit the unit. We can only suggest you replace the part with a factory OEM replacement part. Thanks. Read More...
Chuck R. March 25, 2013 for Model Number ED22GWXTN04 I had previously asked a question about the icemaker not filling all cylinders each cycle and being very sporatic as to how many cylinders were filled each cycle. You recommended replacing the icemaker. Would replacing the icemaker control work or is necessary to replace the entire icemaker?
1 Answer Hello Chuck, This could be the fault of the ice maker control W10190935 water pressure to the ice maker. I would remove the water line from the back of the unit and turn the water on with the line in a bucket. If the water pressure is low, this would explain the issue since the unit fills on a time basis. If the water pressure is good, the ice maker control has bad contacts in it. Read More...
Chuck R March 24, 2013 for Model Number ED22DWXTN04 The ice maker will fill all 8 cylinders when I manually jump it to run its cycle. Then on all cycles thereafter, it may fill 1, 2, 3 or all cylinders. It's very sporatic with mostly getting 1 or 2 cylinders. If I manually jump it to fill the cylinders, I may get all 8 filled the next time or two, then it starts back to 1 or 2 cylinder fills. I have changes the inlet valve and the thermostat. What do I need to do or replace?
1 Answer Hello Chuck. Based on the information you provided, it sounds like the icemaker is bad and will need to be replaced on the unit. Read More...
Kenneth M November 23, 2012 for Model Number ED22RFX My ice make will not make crushed ice and will not eject any ice cubes in the bin. The motor that pushes out the cubes or crushes ice does not work. Suggestions?
1 Answer Hello Kenneth, You may want to check to see if your dispenser bracket WP2180226 is broken. To access this you would use flat blade screw driver under the lower part of dispenser assembly and pop loose. Once off check the pins that hold the switch in place to make sure it is not broken. If the switch is loose the pins are broken and will need to be replaced. Read More...
Mark November 08, 2012 for Model Number ed2jhgxrq00 My icemaker was freezing up at the water inlet and dumping water into the freezer each cycle. I replaced the icemaker, same result. I tested the old wiring harness and the thermal fuse appears to be good. What is wrong and how do I fix it?
1 Answer Hello Mark, The fill tube freezing up is the symptom of a water valve that is leaking through the seal after it closes. You see, when the water valve seal starts leaking, it weeps water into the fill tube slowly enough that it freezes in the fill tube. This can only be corrected by replacing the water inlet valve W10408179. Read More...
Mark November 08, 2012 for Model Number Whirlpool ed2jhgxrq00 My icemaker is freezing up and water overflows into the freezer. I bought the replacement icemaker from you but it appears the thermal fuse may be blown, thus not heating and then freezing up. I can't seem to remove the wiring harness from the sidewall of the freezer. It has an oval cap/plug and there is no screw holding it in place. Does it pull straight out, go up, down, forward back or what??? How do I remove it???
1 Answer Hello Mark. The plug ahould pull out from the wall. If not, you will need to remove the cover of the icemaker and unhook the wiring from there. Read More...
Johnny June 19, 2012 for Model Number 106 626633 The water inlet does not refill icemaker after ice is emptied out of maker. I checked the valve and it works when direct power is applied. Why won't it refill the icemaker?
1 Answer Hello Johnny, There are contacts in the ice maker that energize the water inlet valve. When the ice maker cycles, these contacts should make electrically for 7 seconds to fill the ice maker properly. If the contacts never make electrically, the water inlet valve is never filled and ice cannot be made. Since the model number is incorrect, I can't recommend a part number specifically, but if it is a Whirlpool built model, it probably takes a 4317943 kit. You can just replace the motor module W10190935. Read More...
Eric December 27, 2011 for Model Number ed25texhw00 What size is the inline fuse on wiring harness #1545244 for the icemaker?
1 Answer Hello Eric. The size is not listed and the fuse is not serviceable. If it is bad, you will need to replace the harness WP2187464. Hope this helps. Read More...
Dwaine July 13, 2011 for Model Number Part Number: AP3133181 Of the four wires in this harness, which two are power and which ones land on the solenoid. I am putting the ECKMF-6 icemaker in a small freezer that that is not pre-wired. Thanks
1 Answer Hello Dwaine. Looking at the harness WP2187464, Black is the power for the icemaker, White is the neutral wire, Brown is the water valve, and Green is ground. Hope this helps. Read More...