Admiral Washer LAT2000AAE Leaking

Fix loud grinding or clicking noises during drain cycle. This washer drain pump removes water from the tub. Moderate DIY repair, typically 30-45 minutes.

Fixes washer leaking during drain cycle. This tub to pump hose connects the tub to the drain pump. Simple 3-minute DIY repair with basic tools.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Seals the basket to center shaft, preventing leaks and reducing noise. Replace if leaking between tub and transmission. Confirm fit with your model.

This washer drain hose routes wastewater from the drain pump to your standpipe or laundry tub. Replacing a cracked or kinked hose restores reliable draining and helps prevent leaks during the spin/drain cycle.

• Connects the washer's drain outlet to the household standpipe or laundry tub
• Molded bend helps position the hose correctly and reduces kinking
• Typical symptoms: water leaking at the back or onto the floor while draining
• Visible splits, soft spots, brittleness, or abrasion on the hose
• Slow or incomplete draining caused by kinks or internal blockage

• Disconnect power and move the washer to access the rear; shutting off water is recommended as a precaution
• Place towels or a shallow pan to catch residual water when removing the old hose
• Transfer and reuse existing clamps/brackets if required; fully seat and secure connections, and route the hose to avoid kinks or rubbing
• Insert the outlet end properly into the standpipe or tub per your model's instructions, then run a quick drain/spin to check for leaks

Drive belt transmits motor power to drum for wash and spin cycles. Replace if washer won't spin, makes noise, or belt shows wear. Confirm fit by model.

This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.

• Controls incoming water to achieve correct fill levels and temperature mix
• Addresses no fill, slow/partial fill, or water seeping into the tub when off
• Replaces valves that are electrically failed or mechanically clogged/sticking

• Disconnect power and shut off both water supplies before servicing
• Have towels ready; relieve hose pressure and note wire/hose locations (take a photo)
• Transfer any mounting parts from the original valve if required; avoid overtightening plastic fittings
• Restore water slowly, check for leaks, and run a test fill

This flume hose kit replaces the flexible hose that routes water from the dispenser/fill flume into the washer tub. Restoring a tight, unobstructed hose helps prevent leaks and ensures detergents, bleach, and softener are carried into the wash.

• Directs fill/dispenser water from the flume to the tub during wash and rinse
• Restores proper flow so dispenser compartments empty correctly
• Helps prevent leaks caused by splits, brittleness, or loose connections
• Typical symptoms: water on the floor, dispenser not draining, weak flow into tub, musty odor near dispenser

• Disconnect power and shut off water supply before servicing
• Access the dispenser/flume area by removing the top or control panel per your model
• Note hose routing; transfer and secure clamps; avoid kinks and rub points
• Run a quick fill/rinse to check for leaks at both connections after installation