Frigidaire Dryer GLGR104FSS1 Noisy

The Rear Drum Bearing Kit is an OEM replacement part for Frigidaire dryers. It contains a set of parts responsible for supporting the rear end of the dryer drum, allowing it to rotate smoothly and efficiently during the drying cycle.

Symptoms of a faulty Rear Drum Bearing Kit include:

• Excessive noise or grinding sounds coming from the rear of the dryer
• Difficulty in rotating the drum or drum not turning at all
• Visible signs of wear or damage on the existing bearings
• Increased vibrations or shaking during the drying cycle

Causes of needing to replace the rear drum bearing kit can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or overloading.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models.

NOTE: The metal plate holes are not threaded. Use the self-tapping screws provided in the kit to thread the plate.

The Dryer Drum Bearing is an OEM part for Frigidaire dryers. It supports the dryer drum, ensuring smooth rotation during the drying cycle. This part attaches to the inside of the rear panel of the cabinet, offering support to the dryer drum. 

You should replace the drum bearing if it becomes worn out or damaged. Causes of a bad drum bearing can include normal wear and tear, overloading the dryer, or lack of lubrication.

Symptoms of a bad drum bearing include:

• Loud squeaking or grinding noises during operation
• The drum not turning smoothly or becoming misaligned
• Increased friction causing overheating or burning smells
• The dryer not tumbling clothes properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Drum Belt is an OEM replacement part designed for use with Frigidaire dryers. This critical component is responsible for turning the drum of your dryer, allowing your clothes to tumble freely and dry evenly. 

Causes of a bad Dryer Drum Belt can include wear and tear from regular use, overloading the dryer, which puts extra strain on the belt, or exposure to excessive heat, which can cause the belt to become brittle and break.

Symptoms of a bad Dryer Drum Belt include:

• The dryer motor running but the drum not turning
• Unusual noises, such as thumping or squealing, coming from the dryer when it is running
• The dryer not starting at all, in some cases

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models, ensuring a wide range of users can benefit from its reliable operation.

NOTE: Please note that this dryer drum belt is sold individually. Any additional parts or hardware will require additional purchases.

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Lower Felt Seal is an OEM part for Frigidaire dryers. This part creates a tight seal between the drum and the front panel, preventing air leakage and reducing energy consumption.

Symptoms of a failing Lower Felt Seal include:

• Clothes getting snagged or caught during the drying cycle
• Increased drying times due to heat escaping from the drum
• Excessive noise or squeaking as the drum rotates
• Visible wear, tears, or gaps in the felt seal

Causes of a bad lower felt seal can include regular wear and tear from the constant rotation of the drum, physical damage from overloading the dryer, or deterioration due to exposure to heat and humidity over time.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.

The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.

Symptoms of a failing Rear Drum Support Shaft include:

• Unusual noises, such as thumping or squeaking, during operation
• The dryer drum struggling to rotate or not rotating at all
• Increased wear on other components, such as the belt or motor, due to improper drum alignment

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Blower Housing Assembly is an OEM part for Frigidaire dryers. It houses the blower wheel, which circulates air through the dryer drum and out the exhaust. This assembly ensures that hot air is efficiently directed through the dryer to dry clothes properly.

Over time, the blower housing assembly can become damaged or worn out, affecting the dryer's performance. Causes of a bad blower housing assembly can include accumulation of lint or debris, wear and tear from frequent use, or physical damage to the housing or blower wheel.

Symptoms of a bad Blower Housing Assembly include:

• Reduced or no airflow from the dryer vent
• Unusual noises during operation
• Clothes taking longer to dry
• Overheating or frequent cycling off of the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Idler Arm Pulley is an OEM part for Frigidaire dryers. This part keeps the belt aligned and tight, preventing slippage and contributing to consistent drum rotation. 

Causes of a bad Idler Arm Pulley can range from normal wear and tear, which can degrade the pulley's material or bearings, to improper alignment that puts undue stress on the pulley, leading to premature failure.

Symptoms of a malfunctioning Idler Arm Pulley include:

• Unusual noises, such as squeaking or rumbling, indicating the pulley may be worn or loose
• The dryer drum failing to rotate, even though the motor is running
• Excessive wear or damage to the dryer belt

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Upper Felt Seal is an OEM part for Frigidaire dryers. This felt seal is located at the top edge of the dryer drum and is designed to create a tight seal between the drum and the dryer cabinet. This helps prevent clothes from getting caught in the gap and ensures efficient drying by maintaining proper airflow within the drum. For High Temp adhesive order part number: [AP2153130].

Causes of a bad upper felt seal can include regular wear and tear from frequent use, friction and heat exposure over time, and damage from foreign objects inadvertently caught in the dryer. A compromised seal can lead to inefficient drying, increased wear on clothes, and potential damage to the drum.

Symptoms of a bad upper felt seal include:

• Clothes getting snagged or torn during drying
• Unusual noises such as squeaking or rubbing from the drum area
• Decreased drying efficiency or longer drying times
• Visible wear, thinning, or detachment of the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

The Motor is an OEM part for Frigidaire dryers. It is responsible for driving the drum rotation in the dryer, allowing for the tumbling and drying of clothes. It converts electrical energy into mechanical motion, providing the necessary power to spin the drum and circulate air for efficient drying.

Causes of a faulty dryer motor can include wear and tear over time, electrical malfunctions, or physical damage. These factors can result in issues such as the drum not spinning, unusual noises during operation, or the dryer not heating properly.

Symptoms of a bad dryer motor may include:

• The drum not rotating or spinning
• Unusual grinding or squealing noises while the dryer is in use
• Dryer not generating heat or insufficient drying performance

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test