Frigidaire Range PLEF398ACA Element will not heat

This dual infinite switch controls the inner and outer portions of a dual surface element on your range, providing smooth, adjustable heat levels. Replacing a failed switch restores reliable heating and proper temperature regulation for both ring sizes.

• Regulates power to both the small and large sections of a dual burner
• Typical failure symptoms: only one ring heats, no heat, won't switch between sizes, or heat stuck on high/erratic
• Mounts behind the surface knob and governs burner temperature settings
• Restores consistent simmer-to-boil control across all settings

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access the control panel, then photograph or label all wire positions before removal
• Move wires to the new switch one at a time, matching terminal markings
• Reuse the existing knob; reassemble and test both inner and outer element settings

This surface element control replaces the damaged or worn control that regulates heat to an electric cooktop burner. Restores reliable power and heat adjustment for a single surface element on compatible ranges. What it does

• Acts as the infinite switch that controls the burner's heat level based on the knob setting.
• Replaces a control that causes a burner to stay off, fail to heat, or not respond to knob changes.
• Helps eliminate intermittent heating, erratic temperature changes, or a burner that won't cycle properly.
• Works with the corresponding burner element and knob to provide stepped heat control.

• Disconnect power to the range at the breaker before starting any repairs.
• Basic hand tools required; remove the cooktop or rear console per your model's service instructions.
• Handle terminals and wiring carefully; match wire locations exactly during reassembly.

The Oven Temperature Sensor is an OEM part for Frigidaire ovens. It monitors and regulates the oven's temperature by sending accurate temperature readings to the control board. This ensures that the oven maintains the desired cooking temperature throughout the baking or roasting process.

Causes of a bad oven temperature sensor include exposure to high heat over extended periods, electrical issues, or physical damage to the sensor probe.

Symptoms of a bad oven temperature sensor include:

• Incorrect oven temperatures
• Overheating or underheating during use
• Erratic temperature readings
• The oven not reaching the set temperature

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Broil Element is an OEM part for Frigidaire ovens. This element provides the intense heat necessary for broiling, ensuring that food is cooked evenly and thoroughly from above. It's essential for tasks such as broiling meats, melting cheese, and toasting bread. The element measures 15 3/8 inches from the front to the mounting bracket. It measures 12-1/4 inches wide, and 3 1/4 inches from the bracket to the terminal end. The mounting holes are 11-1/2 inches apart.

You should replace the broil element if it becomes faulty or damaged. Causes of a bad broil element can include regular wear and tear, overheating, or electrical issues that prevent it from heating up properly.

Symptoms of a bad broil element include:

• The broil element not heating up
• Uneven heating during the broiling process
• Visible damage or burn marks on the element
• Sparking or unusual noises when the broil function is used

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.